used Rod heaters for sale

Stock# UG6345 Unused atmospheric cabinet dryer by Airflow Premier Industrial Oven (UK). Chamber construction mild steel. Inside dimensions of drying chamber: W 3250 mm x D 1850 mm x H 2050 mm. Working temperature range up to 60C. Dryer is equipped with 2.2 kW centrifugal fan, whch can give air circullation up to 4.2 air change per minute. Heating - electric - 15 x el heaters each with power 3 kW. Outside dimensions: W 3500 mm x H 2900 mm x D 2200 mm. Machine has local control panel.

Type; AUMA 15SN X 1600 Manufacturer: Berstorff, Germany Year of manufacture: 1998 Technical Specification: Working width: 1600 mm Steel belt width: 1750 mm Steel belt thickness: 1,8 mm Steel belt length: 15600 mm Rolls width: 1950 mm Center distance between frames: 2330 mm Heating roll diameter: 1500 mm Stretch rolls (I, II, III) diameter - 1000 mm Vulcanizing time: 1?30 min Working speed: 7?.210 m/h Max steam pressure in heating roll: 13 bar Max steam pressure in lower stretch roll: 8 bar Surface temperature of: Heating roll: ca. 195oC Lower stretch roll: ca. 175oC Pressure in heating zone between steel belt and rubber: 60 N/cm2 Main motor speed: 1 450 min-1 Drive position: Left from inlet Paint: RAL 6011 Air supply: 6 bar Cooling water supply: + 25oC Max hydraulic pressure Belt pressure tension: 250 bar Belt pressure regulation: ...

Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg

Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg

Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg

76 x 114 cm Feeder Laminator Cutter Bridge Collater Year 2016 (Achillas) Electrical Cabinet 2 x Heaters Vacum Pumps, Fans Covers, Rollers, Pipes Laminator Fan, Manuals, Connecting Tools Pressure Roll It is very good condition Available immediately

Compressor Bitzer Type: S6H-20.2Y Volume: 73.6 m3/h Cooling capacity for R404A: 32 kW at -25°C/40°C, 20 kW at -40°C/40°C, 13 kW at -50°C/40°C Bottle capacity: 73 l Dimensions: 1330x1150x1300 mm Items in magazine: 1 Condition: Used in good condition In set with: Cool Gea Cuba Type: SGKE 50-F61 (x2) Cooling capacity for one: 9,3 kW at DT8, 7,5 kW at DT7 Surface: 39 m2 Air flow: 6300 m3/h Fin spinning: 10 mm Electric heaters Fans: 1x500 mm Dimensions: 1680x800x750 mm Refrigerant: Freon Volume: 13 l Quantity in stock: 2 Condition: Used in good condition Price on request, We have many other equipment : Bitzer, Copeland, Frascold, Lunite, Kueba, Guentner, Eco, Alfa-Laval, Goedhart, Helpman

1x Compressor set with 3 typical minus screw compressors by Bitzer, Compressor type: 3x HSN7471-75-40P Volume: 250 m3/h (x2) Cooling capacity for R404A: 300 kW at -25°C/40°C, 246 kW at -30°C/40°C, 162 kW at -40°C/40°C Oil Separator, Refrigerant tank Photos in attachments 2x Güntner Freezer Cooler Type: S-GHN 081D/312-E Cooling capacity: 94 kW at DT8, 75 kW at DT7 Surface: 400 m2 Air flow: 56,700 m3/h Fin spinning: 12 mm Fans: 3 x 800 mm Dimensions: 3,650 x 1,400 x 2,000 mm Refrigerant: Freon Capacity: 154.1 l Defrosting: Electric heaters in the tray and on the fans, block defrosted with hot gas, Industrial insulated tray Industrial industrial design, Photos in attachments 1x Güntner oil cooler - Photos on request 1x Güntner condenser - Photos on request, The devices worked together,

Cooling unit Bitzer Type: 4HE-18Y-40P Volume: 74 m3/h Cooling capacity for R404A: 52 kW at -5°C/40°C, 35 kW at -15°C/40°C, 22 kW at -25°C/40°C Dimensions: 1750x1250x1050 mm Number of fans: 2x500 mm Quantity in stock: 1 Condition: Used In set with: Cool Thermofin Type: X-TEN 050.2-F-2-12-E Cooling capacity: 19,2 kW at DT8, 14,5 kW at DT7 Surface: 97 m2 Air flow: 12495 m3/h Fin spinning: 12 mm Electric heaters Fans: 2X500 mm Dimensions: 2400X1050X800 mm Refrigerant: Freon Volume: 42.8 l Weight: 227 kg Quantity in stock: 1 Condition: Used in good condition

Bottle heaters CAMES mod. IR 10 Speed: 3.000 bph. Year: 2015. Heating system with infrared lamps Safety protections.

Carel HeaterSteam UR020HL10S isothermal Steam Humidifier Carel HeaterSteam UR020HL10S is an isothermal steam humidifier. It produces steam by heating heating elements immersed in a steam cylinder filled with water. This can be normal tap water or completely demineralized water. The heat generated by the heating elements heats the water up to a temperature of 100 °C. Specifications: Dimensions: (L x W x H): 690 x 438 x 887 mm Weight: 63 kg Steam output: 20 kg/h Power: 15 kW Power supply: 400 V/3 Vapour pressure: 0...3600 Pa Steam connection: 40 mm Water supply connection: 3/4G outside More items - new and used - can be found in our shop! International shipping costs on request!

Manufacturer: MWM Model: TBG632 V16 / SN 2200549 and 2200550 Power: 3620 kW Year of manufacture: 1999 Fuel: Natural Gas Ignition System: TEM Ignition System ZS3 Speed Governor: Heinzmann STG 30-01 Turbocharger type: TPS 57 – D01 Generator: Leroy Somer LSA 56 BL7-6P Control system: TEM-Evo with CPU-1 2.23 Available Equipment: - Engine - Generator - Frame - Turbochargers - TEM-Evo cabinet - Gas Train - Inlet air heaters - Three way Valves HT circuit - Diferential pressure sensor HK and GK water circuits - Oil refilling solenoid Valves - Exhaust gas backpressure sensor protection. Current Status: - Group stopped in running conditions. - Available in our facilities.

ZINCALUM LINE FATA PRODUCTION MACHINERY Manufacturer: FATA PRODUCTION MACHINERY YOM: 1990 Main Equipment: 2 Uncoilers Entry lap welder (Taylor Winfield) 6 Strands Horizontal Entry Accumulator Horizontal Annealing Furnace (Non Ox Heating Section – Radiant Tube Soaking Section: 1 Jet Cooling –Sow Down Cooling Section, Down Chute with electrical heaters AJAX Pre-melt Pot (7 MT) – heated by Two 300 KW channel type inductors AJAX Coating Pot (60 MT) - heated by Four 300 KW channel type inductors. 3roll type Rig. KHOLER Air knives Coating thickness measuring (DMC) 6 Hi Leveller Chemical treatment (Inmersion Tank) Oiler Flying Shear 2 Tension Reels with edge control Strip width range 610 – 1220 mm Strip thickness range 0.30 – 0.85 mm Coil weight entry zone Max 18 MT Coil weight delivery zone Max 9 MT Maximum speed 120 m/min ZNAL  ...

working width 1100mm Calibrating unit with steel shaft Combi unit with rubber roller and boot elastic boot, shot smooth feed speed control Pneumatic oscillation with photocells pneumatic belt tensioning Belt cleaning nozzles on the second unit Activating the shafts from the desktop Year of production 2016

Belt width 150mm Mechanical Oscillation can be sanded on a shoe or surface additional table for sanding irregular edges Possibility of operation without oscillation tilting tops year of production 2008

working width 950mm 1 combi unit Pneumatic boots Flexible segmented ankle boots two feed gears electric table adjustment Pneumatic oscillation motor power 11kW Year of production 2011

The FORNI INDUSTRIALI FIBEX COMBI 6GX-10.130-7110.2E.270 brazing furnace was built by the Italian company Forni Industriali Heat Treating Plants in 2007. The furnace is used for soldering steel elements with solder paste at temperatures up to 1120 degrees Celsius. At the entrance and exit of the furnace, two pairs of gas burners (so-called safety pilots) are installed to prevent the escape of the protective atmosphere outside the furnace. Electric heaters powered by thyristor temperature regulators are responsible for the proper temperature in the furnace. The belt furnace has a conveyor speed adjustment in the range from 0 to 500 mm / min, and the working length of the soldering zone is 7100 mm. The furnace for brazing steel elements was modernized in 2021 - the thermal insulation and the cooling module for sections 1 and 2 were replaced. The cost of the modernization was 70,000 Euro.  ...

Gabler D600 Thermoformer, age 2000:- Unwind Stand Indramat Servomotor Indexing. Top & Bottom Heaters, total Capacity 73.9 kW Indramat Servomotor Forming Station Forming area: 600 x 320 mm Depth of draw neg./pos.: 40/15 mm Stacking and counting Station Counted/ Stacked Products transferred automatically to Delivery Conveyor Waste Material Winder Main Machine PLC Controller: Siemens SIMATIC S5 P3 3A Heater PLC Controller: Siemens SIMATIC S5 95U Operator Touch Pad Control Panel (OPC) : Siemens SIMATIC OP27 Machine has been refurbished in 2014, New set of Cams added during Refurbishment. Excellent Production Condition

Cool Gea Cuba Type: SGLE 103C Cooling capacity: 22.4 kW at DT8, 17.8 kW at DT7 Fin spinning: 12 mm Electric heaters Fans: 3x500 mm Dimensions: 3450x750x670 mm Refrigerant: Freon Volume: 36.8 l Weight: 216 kg Quantity in stock: 1 Reference number: CH 407 Condition: Used in good condition

Juice Pasteurizer Gebhardt EHA45 Electrically Heated 450 l/h Never Installed This Gebhardt juice pasteurizer is specifically designed for fruit juice production in small firms or gardening and horticultural associations. It can handle also juices with pulp and even tomato juices. This Gebhardt EHA45 pasteuriser is equipped with coaxial spiral heat exchanger and hot water circulating pump. The juice tube of a smaller diameter is located inside a larger hot water pipe. Hot water and pasteurised juice move in the opposite direction of each other, ensuring that the juice is warmed evenly. The power of the pasteuriser is step-by-step adjustable according to the number of operating heaters. The thermostat keeps the hot water temperature at a desired level selected by the user, which should be 4-5 degrees warmer than the temperature of the juice that comes out. The juice temperature is ad ...

Juice Pasteurizer Gebhardt EHA45 Electrically Heated 450 l/h Never Installed This Gebhardt juice pasteurizer is specifically designed for fruit juice production in small firms or gardening and horticultural associations. It can handle also juices with pulp and even tomato juices. This Gebhardt EHA45 pasteuriser is equipped with coaxial spiral heat exchanger and hot water circulating pump. The juice tube of a smaller diameter is located inside a larger hot water pipe. Hot water and pasteurised juice move in the opposite direction of each other, ensuring that the juice is warmed evenly. The power of the pasteuriser is step-by-step adjustable according to the number of operating heaters. The thermostat keeps the hot water temperature at a desired level selected by the user, which should be 4-5 degrees warmer than the temperature of the juice that comes out. The juice temperature is ad ...

Cool Goedhart Type: VCI-B 82506E Cooling capacity: 26 kW at DT8, 19kW at DT7 Fin spinning: 6 mm Electric heaters Number of fans: 2 x 500 mm Device dimensions: 2450 x 1250 x 700 mm Refrigerant: Freon Capacity: 38 L Stock status: 1 piece Stock number: CH 241 Condition: Used Price on request, We have many other Kealteanlagen : Bitzer,Copeland,Frascold,Lunite,Kueba,Guentner,Eco,Alfa-Laval,Goedhart,Helpman

GRASO PK030 shrink wrapping machine with GRASO TGW 30/80 heat shrink tunnel was manufactured in Poland in 2014 by Graso. The device, due to its versatility and advanced technology, optimises the process of packaging various types of products in unit packs as well as collective packages. Packaging made of heat shrink film effectively protects products from external factors, while enhancing their aesthetic qualities at the same time. The GRASO PK 030 packing machine has a large working area and a knurled bar, which guarantees excellent sealing quality. After sealing, a roller conveyor transports the product to the heating tunnel, where the film shrinking process takes place. After exiting the heating chamber, the finished pack is cooled by fans. The GRASO TGW heat shrink tunnel, in turn, is equipped with a control box, heaters with heat sinks and adjustable airflow by means of adjustabl ...

working width 600mm two brushing rollers smooth feed speed control up/down shaft adjustment shafts independently adjustable Year of production 2013 weight 720kg power supply 380V

Cool Guntner Type: GHN 066A/37 Cooling capacity: 36.6 kW at DT8, 29 kW at DT7 Fin spinning: 7 mm Electric heaters Fans: 3 x 660 mm RPM: 870/650 Dimensions: 4300 x 750 x 1000 mm Refrigerant: Freon Volume: 51 L Weight: 330 kg Pieces in stock: 2 Reference number: CH371 Condition: Used

Cool Guntner Type: GHN080.2F/210-E Cooling capacity: 54 kW at DT8, 43 kW at DT7 Surface: 235 m2 Air flow: 37 320 m3/h Fin spinning: 10 mm Electric heaters Fans: 2 x 800 mm Dimensions: 4000 x 900 x 1300 mm Refrigerant: Freon Volume: 86.5 l Waga: 460 kg Items in stock: 3 Reference number: CH 392 Price on request, We have many other equipment : Bitzer, Copeland, Frascold, Lunite, Kueba, Guentner, Eco, Alfa-Laval, Goedhart, Helpman

Cool Guntner Type: GHNE 065C / 28 Cooling capacity: 30 kW with DT8, 23 kW with DT7 Fin spinning: 8 mm Electric heaters Number of fans: 2 x 650 mm Device dimensions: 3000 x 750 x 1000 mm Refrigerant: Freon Capacity: 46 L Stock status: 5 pieces Stock number: CH 236 Condition: Used Price on request, We have many other Kealteanlagen : Bitzer,Copeland,Frascold,Lunite,Kueba,Guentner,Eco,Alfa-Laval,Goedhart,Helpman

Cool Guntner Type: S-GHN 040C/312-E Cooling capacity: 16 kW at DT8, 13 kW at DT7 Fin spinning: 12 mm Electric heaters Fans: 3 x 400 mm RPM: 2840 Dimensions: 2950 x 950 x 600 mm Refrigerant: Freon Volume: 28 L Weight: 135 kg Pieces in stock: 2 Reference number: CH372 Condition: Used Price on request, We have many other equipment : Bitzer, Copeland, Frascold, Lunite, Kueba, Guentner, Eco, Alfa-Laval, Goedhart, Helpman

Cool Guntner Type: S-GHN080.2H/310-E Cooling capacity: 100 kW at DT8, 80 kW at DT7 Surface: 469 m2 Air flow: 53 910 m3/h Fin spinning: 10 mm Electric heaters Fans: 3 x 800 mm Dimensions: 5600 x 1050 x 1300 mm Refrigerant: Freon Volume: 167.5 l Waga: 750 kg Pieces in stock: 2 Reference number: CH 391 Condition: Used in good condition Price on request, We have many other equipment : Bitzer, Copeland, Frascold, Lunite, Kueba, Guentner, Eco, Alfa-Laval, Goedhart, Helpman

H.E.F. HEF DURFERRIT salt bath nitriding line was built in 2001. This highly advanced production line makes it possible to improve the mechanical properties of the workpiece by increasing its strength and resistance to wear and corrosion. To achieve this, the workpieces undergo thermo-chemical treatment in the form of salt bath nitriding, which results in an anthracite or black colour and a surface hardness of up to 1300 HV. The H.E.F. HEF DURFERRIT thermo-chemical treatment line has been continuously serviced and upgraded throughout its service life. About 2.5 years ago, the lining and heaters were overhauled and the main nitriding ladle was replaced. It is also possible to purchase a new spare main ladle for the offered machine at an additional cost. The production line includes: – a ladle for washing/rinsing workpieces (3 pcs.) – plunge pre-heating furnace – SURSULF nit ...

Used ILLIG RDK 54 Thermoforming Line, Age 1995 Unwind Stand Indramat Servomotor Indexing Max. Film width 610 mm max. Thickness range 0.18 to 2.5 mm. Hardened Transport Rails, Double Heating, Heating Load 41.0 kW. Heaters move forwards automatically with pneumatic control Sheet Sag Control Form Area 550 x 400 mm Forming & Punching in Mold with integrated Steel Rule Die. Positive Draw 20 mm, Negative Draw 20 to 40 mm Trimming Force 50kN. Top and Lower Platens Moved by separate Indramat Servomotors Heavy duty Toggles on both upper & Lower Platen Stacking/ Counting Station Waste Material Winder Inline ILLIG RS75b Grinder with Sound Proof Housing & Controls. Suitable for PS, OPS, PP, PE, PVC etc.

Unwind Stand Preheater ILLIG VHW 72/ 2 ILLIG RDM 70K Thermoformer with auto-start facility Indramat Servomotor Indexing Top & Lower heaters Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Pneumatic Plug Assist, Max. Part height 125 mm Control Cabinet with Optimised Schleicher (PLC) Controls Auto Lubrication Pump. Inline ILLIG ÜG70B Counter/ Stacker, with delivery conveyor Inline Grinder

Unwind Stand Preheater ILLIG VHW 72/ 2 ILLIG RDM 70K, age 1989 Thermoformer with auto-start facility SEW Eurodrive Servomotor Indexing Max. material width 730 mm Max. Indexing length 300 mm Top & Lower heaters, total connected load top & bottom heaters 74.2 kW Drive Motor 6.93 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Hydraulic Plug Assist, Max. Part height 125 mm Hydraulic Power Pack Control Cabinet with Optimised Schleicher (PLC) Controls Encoder on Main Shaft Auto Lubrication Pump. Inline ILLIG UG70b Counter/ Stacker Delivery Conveyor for Counted/ Stacked Cups with Ejector Table

Unwind Stand Preheater ILLIG VHW 72/ 2 ILLIG RDM 70K (refurbished in 2003) Thermoformer with auto-start facility Indramat Servomotor Indexing Top & Lower heaters Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Pneumatic Plug Assist, Max. Part height 125 mm Control Cabinet with Optimised Schleicher (PLC) Controls Auto Lubrication Pump. Inline ILLIG ÜG70B Counter/ Stacker, with delivery conveyor Inline Grinder & Blower

Illig RDM75K age 1998, refurbished in 2019, with Siemens S5 PLC Controls, used only for ca. 50,000 hrs ELAU B1 Display with Touchpad controls Thermoformer with auto-start facility Indramat Servomotor Indexing Max. material width 750 mm Max. Indexing length 480 mm Top & Lower heaters, total connected load top & bottom heaters 111.3 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 700 x 450 mm Hydraulic Cylinder Plug Assist with Bosch Rexroth Hydraulic Power Pack, completely Overhauled in 2019 Max. Part height 150 mm Max. Mold closing force 25,000 daN Auto Lubrication system Siemens S5 PLC Controls New original ILLIG/ RITTAL Control Cabinet Cooling System added in May-2023.

Vacuum machine, single chamber Efficient vacuum machine of exceptional quality for vacuum packaging of meat, cured meat products, fruits and vegetables Ideal for fast food facilities, hotels, restaurants and other catering facilities Dimensions: 540 × 490 × 540mm Heaters: 2 x 40 cm Electrical power: 1.5kW Weight: 59 kg

Two-chamber vacuum machine Ital Form Dimensions of the machine: 1845×868×1020mm Chamber dimensions: 880x755x170mm Sealing length: 820mm Number of heaters: 2 Electric power: 3kW Weight: 295kg

McIntyre 900 Shear A reliable workhorse equipped with 920mm (36.25) blades to allow you to handle larger pieces of material with ease All round yard shear Designed to give maximum possible blade length without losing cutting capacity, the 900 shear is perfect for a wide variety of yard uses, in particular the handling of larger pieces of non-ferrous scrap. The 900 can be fitted with solenoid control allowing it to be coupled to infeed or outfeed conveyors. Other optional equipment for the 900 shears includes oil-immersed tank heaters, forced air cooling and infeed table to handle oversized material

JR Dare Press Plate: 1400mm x 1400mm Daylight 530 mm 4 x rams Ram diameter - 16” Max working pressure - 1500 PSI Clamping tonnage - 600T Platen heating - strip heaters 18KW / platen

Complete Krones PET filling line for CSD capacity: 22.000 bph by 1,5 ltr. bottles year: 2005 / 2009 / 2013 / 2015 Blowmoulding-Filler-Bloc Blowmoulding KRONES Contiform S16 rotary machine with 16 blowing stations heating module KZM09 with 14 heaters blowing air recovery system Airwizard 2 including: preform tipper chute elevator and horizontal conveyor roller orientor VZT-3011, Make Tanner incl. blowing moulds for 1500 ml bottle and 500 ml bottle Preform rinser KronesPrejet 30 year of manufacturing: 2005 rotary machine with 30 rinsing valves year of manufacturing: 2005 Chiller TEAevo301, Make MTA year of manufacturing: 2013 cooling capacity 65 kW (36°C, 50Hz) Filler KRONES Volumetic type: VODM-PET-4.320-120-113-SV15 year of manufacturing: 2005 with 120 filling valves, pitch: 113mm plastic screw capper with 15 heads clean room with 5 roof filt ...

Kündig Duplex 1350 E Quality product from Switzerland CONSTANT TABLE MACHINE / automatic Headhead delivery Wide-belt calibration fine grinding machine 1. Power Unit: Contact Roller Grinding Unit 90 Shore Contact roller level infinitely adjustable according to grain scale 2. Unit: Sanding pad unit with electronically controlled segment sanding pad Belt drive motor power 15 kW Working width 1350 mm Max. workpiece thickness 160 mm Feed speed 3-15m/min. infinitely variable  Automatic workpiece thickness adjustment  ENORMATIC quick adjustment with feed release (for long workpieces) PLC control with LCD screen control to automate and manage all work programs Infeed and outfeed tables with roller support additional. Tables in the inlet and outlet - foldable Machine is WORKSHOP overhauled in TOP CONDITION  from stock Lieboch

Kündig Duplex 1350 KdS-E Brilliant + Lack Quality product from Switzerland CONSTANT TABLE MACHINE / automatic Headhead delivery Wide-belt calibration fine grinding machine 1st unit: Combination unit contact roller 90 Shore and sanding pad unit with electronically controlled segment sanding shoe Contact roller level infinitely adjustable according to grain scale Swivelling grinding unit for diagonal grinding Stepless sanding belt speed 3 - 18 m/sec Oscillating band radiation 2. Unit: Sanding pad unit with electronically controlled segment sanding pad Belt drive motor power 15 kW Working width 1350 mm Max. workpiece thickness 160 mm Feed speed 3 - 15 m/min infinitely variable Stable vacuum table with lacquered carpet Automatic workpiece thickness adjustment ENORMATIC quick adjustment with feed release (for long workpieces) PLC control with LCD screen control to automate a ...

Used automatic tray packing machine, model B 700 PAR Multifile Mag Manufacturer: MONTPACK Country: Italy New: 1992 Machine capacity: 6-7 packages/min The maximum packet size: 720 x 400 x 380 mm Supply voltage: 380 V Power: 18 kW Power consumption: 10-12 kW / h The maximum diameter of the film roll: 300 mm The maximum length of the film roll: 720 mm Compressed air supply pressure: 6 bar Machine weight: 800 kg Dimensions: 6.1 x 2.5 x 2.2 m (L. X width. X height.)   The machine forms 2x3 packages with PET bottles 1l trays without flanges shrink-wrapped in foil. Shrink tunnel is equipped with a 15-heaters, dual chamber with two ventilation systems; operates at 220 ° C.

Block size press Müro 4x5000/A2 WT; cleaned and tested; 3x dryer; insertion width 700mm; Insertion height 525mm. Padding press Müro 4x5000/A2 WT; cleaned and checked; three heaters; working width 700mm; working hight 525mm.

Block size press Müro 4x5000/A3 WT; cleaned and tested; 2x dryer; insertion width 525mm; Insertion height 525mm. Padding press Müro 4x5000/A3 WT; cleaned and checked; two heaters; working width 525mm; working hight 525mm.

USED CENTRIFUGAL MOLECULAR DISTILLATION SYSTEM Manufacturer: MYERS VACUUM, Inc. Model: PILOT 15 LAB Throughput Capacity 10 - 80 lbs/hr (4.5 – 36.3 kg/hr) Type Continuous Pumping system ultimate pressure: 2 X 10-4 Torr Operating Pressure 10 -3 Torr to Atmosphere Mechanical Forepump >11 CFM High Vacuum Pump 320 L/sec of air at 250C. Power: 10-15 KW/ hour 3 phase wye” 115/208 V, 5 wire 50/60 HZ Available for 230, 415 or 460 Volt. Water: (20°C) 2 gal/min (7.6 L/min) Liquid nitrogen consumption: 0.5 liters/ hour (Utility consumptions may vary depending on process conditions) Dimensions: Height 69 Inches (1.75m), Width 34 Inches (.86m), Depth 59 Inches (1.5m) Net Weight 1300 lbs. (590kg) Centrifugal molecular distillation is a purification technique, which has gained wide acceptance in the chemical, food processing, pharmaceutical, and petroleum industries as well as  ...

Stock# U2441-1 Used stainless steel pilot plant belt dryer by Neuweiler AG (CH). Dryer has a belt designed in stainless steel net, with total width 300 mm, working width 250 mm. Total length of belt about 830 cm. At the feeding section there is a rotating turbine with adjustable rotation and height, for proper positioning the product on the belt. Turbine is driven by el motor 0.18 kW. Drying chamber has insulated walls and has working length 207 cm. Belt is driven by reducer and el motor 0,55 kW, 1380 rpm, 230/400 V, 50 Hz. Working speed of belt is adjustable. Dryer is equipped with stainless steel main air blower driven by el. motor 11 kW. Air is transfered via chamber with electric heaters and is blowing on the belt from the top. There is also exhaust fan. Dryer has electric cabinet and local control panel. All is mounted on stainless steel frame with 6 legs.

PART NUMBER: 7549 Specifications: - max width of the workpiece 1100mm - max height of the workpiece 170mm 2 units: 1) grooved rubber roller for calibrating 2) rubber roller + boot boot + metal roller –in advance: - metal roller, slip - aggregate - metal roller, slip - A unit with a shoe - metal slip outfeed roller – from below: - Pulling strap - pneumatic oscillation of the belts - electric lifting of the table top - 2 types of feed speeds - 11kW motor - with pneumatic brake - working pressure 6-8bar - extraction spigot diameter 2x150mm - total dimensions length/width/height 1960x1700x2000mm - weight about 2000kg ADVANTAGES – made in Germany – 2 units – unpainted – used grinder, very good condition Net price: 34900 PLN Net price: 8116 EUR depending on the price 4.30 EUR (Prices may change with higher fluctuations)

Process tank 450 l · vertical tank · pressure tank up to 2 bar · main tank made of stainless steel AISI 316Ti · tank insulated with mineral wool with a thickness of 50 mm in the cylindrical part and on the bottom end outer jacket made of stainless steel AISI 316Ti, thickness 2mm · bottom and top bottom pressed DIN 28011 · heating jacket for glycol · circulation pump · heating medium temperature sensor · expansion vessel of the heating system electric heaters - 5 pcs. 4.5kW/400V · control box: controlled by the heating system and the operation of the stirrer · heating medium supply connector DN33.7 · connector for receiving the heating medium DN33.7 Equipment: · manhole DN300 (2 bar) with a safety sensor drain connection (heated) filling connector (heated) · filling level sensor connector · PT-100 temperature level connector · safety valve · Redox + e ...

Used line for the production of the co-extrusion by PST Forming method. PTI - The twin screw extruder DS 92/28   2x screws with a diameter of 92 mm The length of screws 28 x L / D Snails closed system with internal temperature control, deep nitrided, with degassing on the cylinder, extruder equipped with a vacuum pump with filter, Siemens Servo Motor power: 60 KW Torque: Nm 15700 Screw rotation: 0 - 50 rev. / Min. Zones with ceramic heaters with an intense cooling: 5 x 5 KW Cooling Zones: 4 Performance with hard PVC, depending on the materials and tools: max.600kg / h Length: 4500 mm Width: 1600 mm Height: 2300 mm           Extruder equipped with a microprocessor control SIEMENS type Extrusion Pro Pak visualization 2. Co-Extruder PTI - The twin screw extruder DS 68/28 Snails with a diameter of 2 x 68 mm Length of the screws: 28 x L / D Snails cl ...