Arburg 820S 4000-2100 / Production line with the Arburg Multilift robot Year of manufacture: 12.2010 Injection unit: Screw diameter: 70 mm Injection weight: 984 g Spray pressure: 2000 bar Dosing volume: 1078 ccm Clamping unit: Clamping force: 400 t Tiebar spacing: 820x820 mm Size of the clamping plates: 1171x1171 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Production line with the Arburg Multilift robot Machine in very good technical condition Euromap 67 Robot interface Control with air valve Hydraulic core pull x 4 Control with hot runners x 12 Hardened injection unit - Bimetal Proportional valve on the injection unit – precise injection The machine was regularly serviced in Germany Arburg Multilift robot Year of manufacture: 12.2010 5-axis robot: 3 axes are driven by servo motors (electric); ...

screw size: 70 mminjection shot weight in Polystyrol: g/PSclosing pressure: 400 kNtotal power requirement: kWweight of the machine ca.: 19 trequired space: 15 x 2.5 x 2.2 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Arburg 820S 4000-2100/400 / Production line with the Sepro Industrial Robot SR S5-35 S3 Trans robot / Operating hours: 42,014 h in automatic mode Year of manufacture: 09.2012 Injection unit: Screw diameter: 60 mm Injection weight: 723 g Spray pressure: 2500 bar Dosing volume: 792 ccm Clamping unit: Clamping force: 400 t Tiebar spacing: 820x820 mm Size of the clamping plates: 1171x1171 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: 2K Injection Molding Machine with Turntable and Robot Very good technical condition Operating hours: 42,014 h in automatic mode Euromap 67 Robot interface Air Valve x 6 Hydraulic, needle-core pull, controlled by a proportional valve x 4 pairs Control with hot runners x 24 Reinforced Injection Units – Bimetal Proportional valve on vertical injection unit – precise injection ...

screw size: mminjection shot weight in Polystyrol: g/PSclosing pressure: kNtotal power requirement: kWweight of the machine ca.: trequired space: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Arburg 1500T 3200-1300 e² / Hybrid machine with a turntable Year of Make: 2011 Injection unit: Screw diameter: 60 mm Injection weight: 607 g Spray pressure: 2000 bar Dosing volume: 664 ccm Clamping unit: Clamping force: 320 t Spar spacing: 0x0 mm Size of the clamping plates: 1510 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Hybrid machine: high-speed, energy-saving and very quiet Operating hours: approx. 30,000 in automatic mode Euromap 67 Robot interface Control with air valve Hydraulic core pull x 3 Control with hot runners x 13 Hardened injection unit - Bimetal Main motor of the machine – servo motor driven by inverter Very precise rotary table, driven by a servo motor, controlled by an inverter Rotary table diameter: 1500 mm Horizontal injection unit with automatic injection height adjustment ...

(1) Gas (2) Fuel (3) Electric: 0  Temperature maximum: 0 C°Capacity (kg): 0 kg Technical dataWorking space:Width: 600 mmHeight: 650 mmdepth: 800 mmExternal dimensions:Length: 1200 mmWidth: 900 mmHeight: 2000 mm

Arburg 570S 2200-1300 / Production line with the Arburg Multilift robot Year of manufacture: 11.2010 Injection unit: Screw diameter: 60 mm Injection weight: 607 g Spray pressure: 2000 bar Dosing volume: 664 ccm Clamping unit: Clamping force: 220 t Handlebar spacing: 570x570 mm Size of the clamping plates: 795x795 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Production line with the Arburg Multilift robot Machine in very good technical condition Euromap 67 Robot interface Air Valve x 3 Hydraulic core pull x 4 Control with hot runners x 12 Hardened injection unit - Bimetal Proportional valve on the injection unit – precise injection The machine was regularly serviced in Germany Arburg Multilift robot Year of manufacture: 11.2010 5-axis robot: 3 axes are driven by servo motors (electric); Axis B ( ...

Clamping force: 1 tTie bars distance: 1 mmDay light: 1 mm Preheating / Drying For manual, cycle and CNC processing up to interactive contour programmingCovered guidance tracks (DGP) for high long-term precisionDirect drive from motor to main spindle for high running smoothnessOil recirculating lubrication unit with filtering for the lubrication of the precision main spindle bearingCombination control unit for economically advantageous programming and machine operation, as well as optimum access to the work area  Chamber inside 2000 x 1250 x 1250 mm Volume inside 2344 Liter Up to 400 Gr/C (Power 33kW)

Arburg 570S 2200-290/100/100 / Production line with the Wittmann W823 robot / Operating hours: 20,499 h in automatic mode Year of Make: 2016 Injection unit: Screw diameter: 35 mm Injection weight: 132 g Spray pressure: 2000 bar Dosing volume: 144 ccm Clamping unit: Clamping force: 220 t Handlebar spacing: 570x570 mm Size of the clamping plates: 795x795 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: 3-component injection moulding machine, high-speed Very good technical condition Operating hours: 20,499 h in automatic mode Euromap 67 Robot interface Air Valve x 6 Hydraulic, needle-core pull, controlled by a proportional valve x 4 Control with hot runners Hardened injection unit - Bimetal Proportional valve on the injection unit – precise injection Machine with two cylinders / battery with compressed ni ...

Ref. no.: 17505Hersteller: DEMAGYear of construction: 1997Clamping unitClamping force: 35 tonOpening stroke: 350 mmDistance between tie bars: 320 x 320 mmMould height min.: 180 mmPlaten size (h x v): 460 x 450 mmInjection unitScrew diameter: 18 mmInjection volume: 23 cm³Shot weight: 20 gInjection pressure: 2868 barMeasurements and weightDimensions: 3,3 x 1,2 x 2,0 mMachine weight: 2700 kg

Arburg 520C 2000-675 with the Wittmann 821 robot Year of manufacture: 07.2001 Injection unit: Screw diameter: 45 mm Injection weight: 240 g Spray pressure: 2500 bar Dosing volume: 286 ccm Clamping unit: Clamping force: 200 t Tiebar spacing: 520x520 mm Size of the clamping plates: 685x685 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA Additional equipment: Euromap 12 Robot interface Control with air valve Hydraulic core pull x 2 Hardened injection unit - Bimetal Robot Wittmann W821 Year of Make: 2011 4-axis robot: 3 axes are driven by servo motors (electric); Axis C - pneumatic Traversing in axes: X-550, Y-1200, Z-2500 Touch control panel The safety package for robots Robot with adapter and protective housing Purchase of the robot at an additional cost Metrics: Weight: 6630 kg Length/Width/Height: 5.53x1.93x2.22 m All offered  ...

Ref. no.: 18330Hersteller: ARBURGYear of construction: 2003

Arburg 570H 2000-2100 with the Sepro Industrial Robot SDR 22S robot / Hybrid machine / Operating hours: approx. 29,000 h in automatic mode Year of Make: 2010 Injection unit: Screw diameter: 70 mm Injection weight: 984 g Spray pressure: 2000 bar Dosing volume: 1078 ccm Clamping unit : Clamping force: 200 t Handlebar spacing: 570x570 mm Size of the clamping plates: 795x795 mm Ejector: hydraulic Clamping unit: toggle lever Control: SELOGICA - Touchscreen Additional equipment: Machine in very good technical condition Hybrid machine: high-speed, energy-saving and very quiet Operating hours: approx. 29,000 h in automatic mode Euromap 67 Robot interface Air Valve x 2 Hydraulic core pull x 1 Air Core Pull x 7 Control with hot runners x 15 Hardened injection unit - Bimetal Main motor of the machine - Servo motor driven by inverter - Energy saving The injection u ...

Ref. no.: 18482Hersteller: KRAUSS MAFFEIYear of construction: 2010Clamping unitClamping force: 300 tonOpening stroke: 820 mmDistance between tie bars: 810 X 720 mmMould height min.: 480 mmOpening width: 1300 mmInjection unitScrew diameter: 60 mmInjection volume: 792 cm³Shot weight: 720 gInjection pressure: 2420 barMeasurements and weightDimensions: 6,7 X 2,1 X 2,4 mMachine weight: 16400 kgRobotProducer: Krauss Maffei Type: KM LRX S 250 Year: 2010

Arburg 570C 2000-800 / Operating hours: 4,403 in automatic mode Year of Make: 2011 Injection unit: Screw diameter: 45 mm Injection weight: 291 g Spray pressure: 2470 bar Dosing volume: 318 ccm Clamping unit: Clamping force: 200 t Handlebar spacing: 570x570 mm Size of the clamping plates: 795x795 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Machine in very good technical condition Operating hours: 4,403 in automatic mode Euromap 67 Euromap 12 Robot interface Air Valve x 1 Hydraulic core pull x 2 Hardened injection unit - Bimetal Purchase of the machine by the first owner in 2012 Metrics: Weight: 7440 kg Length/Width/Height: 5.53x1.79x2.20 m All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected m ...

Ref. no.: 18061Hersteller: ARBURGYear of construction: 2003Clamping unitClamping force: 80 tonOpening stroke: 450 mmDistance between tie bars: 420 x 420 mmMould height min.: 250 mmMould height max.: 700 mmPlaten size (h x v): 570 x 570 mmInjection unitScrew diameter: 25 mmInjection volume: 54 cm³Shot weight: 49 gInjection pressure: 2500 barMeasurements and weightDimensions: 3360 m

Arburg 470C 1500-400 Year of manufacture: 07.2009 Injection unit: Screw diameter: 45 mm Injection weight: 232 g Spray pressure: 1580 bar Dosing volume: 254 ccm Clamping unit: Clamping force: 150 t Spar spacing: 470x470 mm Size of the clamping plates: 650x650 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Core train control Hardened injection unit - Bimetal It is possible to change the screw diameter Metrics: Weight: 4790 kg Length/Width/Height: 4.44x1.63x2.09 m Drive: Pumps/motor: 18.5 kW Heating capacity: 9.4 kW Total power: 27.9 kW All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical tests at our company in Łódź. Price: On request

Ref. no.: 18410Hersteller: ARBURGYear of construction: 2007Clamping unitClamping force: 80 tonOpening stroke: 500 mmDistance between tie bars: 420 X 420 mmMould height min.: 250 mmOpening width: 750 mmPlaten size (h x v): 570 X570 mmInjection unitScrew diameter: 35 mmInjection volume: 144 cm³Shot weight: 121 gInjection pressure: 1820 barMeasurements and weightDimensions: 4,3 X 1,60 X 2,0 mMachine weight: 3200 kg

Arburg 520S 1600-290/100 / Production line with the Wittmann W823 robot / Operating hours: 20,181 h in automatic mode Year of manufacture: 09.2011 Injection unit: Screw diameter: 35 mm Injection weight: 132 g Spray pressure: 2000 bar Dosing volume: 144 ccm Clamping unit: Clamping force: 160 t Tiebar spacing: 520x520 mm Size of the clamping plates: 695x695 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: 2K Injection Molding Machine with Turntable and Robot Very good technical condition Operating hours: 20,181 h in automatic mode Total number of operating hours: 28,473 h Euromap 67 Robot interface Air Valve x 3 Hydraulic, needle-core pull, controlled by a proportional valve x 2 Reinforced Injection Units – Bimetal Proportional valves on sprinkler units - precise spraying Machine with two cylinders / bat ...

Ref. no.: 18552Hersteller: BOYYear of construction: 1997Clamping unitClamping force: 22 tonOpening stroke: 200 mmDistance between tie bars: 254 mmMould height min.: 200 mmMould height max.: 400 mmPlaten size (h x v): 425 x 400 mmInjection unitScrew diameter: 28 mmInjection volume: 49 cm³Shot weight: 44 gInjection pressure: 1069 barMeasurements and weightDimensions: 2.3 x 0.81 x 1.63 mMachine weight: 760 kg

Battenfeld TM 300/2250 Clamping force: 300t Year of Make: 2014 Injection weight in hp: 980g Injection Unit .../2250 Screw diameter: 65 mm Spec. Spray pressure: 2070 bar Injection volume: 1078 ccm Injection weight in hp: 980 g Hydr. Drive power: 63 kW Cylinder heating capacity: 26 kW L/D Screw Ratio: 22 Clamping Unit 300/... Clamping force: 300 t Size of the clamping plates: 1020 x 940 mm Clearance spar spacing: 630 x 630 mm Ejector force: 59 kN Tool installation height: 250...650 mm Opening travel: 600 mm Max. plate spacing: 1250 mm Ejector travel: 200 mm Total connected load: 2222 kW Fuel tank capacity: 550 l Electrical connection (fuse): 1111 A Weight: 11800 kg Dimensions(m) LxWxH: 7.0 x 1.8 x 2.4 m Year of Make: 2014

Ref. no.: 18404Hersteller: ARBURGYear of construction: 2001Clamping unitClamping force: 130 tonOpening stroke: 500 mmDistance between tie bars: 420 x420 mmMould height min.: 250 mmOpening width: 750 mmPlaten size (h x v): 605 x 605 mmInjection unitScrew diameter: 45 mmInjection volume: 230 cm³Shot weight: 210 gInjection pressure: 1670 barMeasurements and weightDimensions: 4,68 x 1,3 x 2,2 mMachine weight: 5100 kgAdditional information & extrasCore pull: 1 pcs

Battenfeld TM 300/2250 Clamping force: 300t Year of Make: 2014 Injection weight in hp: 980g Injection Unit .../2250 Screw diameter: 65 mm Spec. Spray pressure: 2070 bar Injection volume: 1078 ccm Injection weight in hp: 980 g Hydr. Drive power: 63 kW Cylinder heating capacity: 26 kW L/D Screw Ratio: 22 Clamping Unit 300/... Clamping force: 300 t Size of the clamping plates: 1020 x 940 mm Clearance spar spacing: 630 x 630 mm Ejector force: 59 kN Tool installation height: 250...650 mm Opening travel: 600 mm Max. plate spacing: 1250 mm Ejector travel: 200 mm Total connected load: 2222 kW Fuel tank capacity: 550 l Electrical connection (fuse): 1111 A Weight: 11800 kg Dimensions(m) LxWxH: 7.0 x 1.8 x 2.4 m Year of Make: 2014

Ref. no.: 16369Hersteller: BATTENFELDYear of construction: 2005Clamping unitClamping force: 75 tonOpening stroke: 800 mmDistance between tie bars: 405 x 405 mmMould height min.: 150 mmMould height max.: 480 mmInjection unitScrew diameter: 18 mmInjection volume: 30 cm³Shot weight: 27 gInjection pressure: 2440 barMeasurements and weightDimensions: 4,5 x 1,7 x 2,0 mMachine weight: 4500 kg

Arburg Allrounder 270S 250-60 Clamping force: 25 t Year of Make: 1999 Injection weight: 17 g Injection Unit 60 Screw diameter: 18 mm Specific injection pressure: 2500 bar Injection volume: 20 cc Injection weight: 17 g L/D ratio of screw: 24.5 Clamping unit 250 Clamping force: 25 t Panel size: 400 x 400 mm Lights spar spacing: 270 x 270 mm Tool height: 200 mm Opening travel: 275 mm Maximum panel spacing: 475 mm Electrical connection (fuse): 120 l Weight: 1900 kg Control: Selogica equipment: -Sorting flap -Euromap 12 interface -Picker

Ref. no.: 18255Hersteller: ENGELYear of construction: 2004Clamping unitClamping force: 180 tonOpening stroke: 750 mmDistance between tie bars: 960 x830 mmMould height min.: 500 mmOpening width: 1250 mmInjection unitScrew diameter: 45 mmInjection volume: 318 cm³Shot weight: 302 gInjection pressure: 1769/2360 barMeasurements and weightMachine weight: 13500 kgRobotProducer: Wittman Type: W743 Year: 2009

Arburg Allrounder 270S 250-60 Clamping force: 25 t Year of Make: 1999 Injection weight: 17 g Injection Unit 60 Screw diameter: 18 mm Specific injection pressure: 2500 bar Injection volume: 20 cc Injection weight: 17 g L/D ratio of screw: 24.5 Clamping unit 250 Clamping force: 25 t Panel size: 400 x 400 mm Lights spar spacing: 270 x 270 mm Tool height: 200 mm Opening travel: 275 mm Maximum panel spacing: 475 mm Electrical connection (fuse): 120 l Weight: 1900 kg Control: Selogica equipment: -Sorting flap -Euromap 12 interface -Picker

Ref. no.: 18142Hersteller: DEMAGYear of construction: 1997Clamping unitClamping force: 50 tonOpening stroke: 400 mmDistance between tie bars: 355 x 355 mmMould height min.: 210 mmPlaten size (h x v): 540 x 540 mmInjection unitScrew diameter: 35 mmInjection volume: 106 cm³Shot weight: 95 gInjection pressure: 2573 barMeasurements and weightDimensions: 3,65 x 1,15 x 1,18 mMachine weight: 3600-2500 kg

Arburg Allrounder 320S 500-60 Clamping force: 50t Year of manufacture: 09/2005 Injection weight: 27g Injection Unit .../60 Diameter of the screw: 22 mm Specific injection pressure: 2340 bar Injection volume: 30 cc Injection weight: 27 g L/D ratio of screw: 20 Tool clamping system 500/... Clamping force: 50 t Tool plate dimensions: 446 x 446 mm Distance between columns: 320 x 320 mm Tool height: 225 mm Opening travel: 350mm Maximum spacing of the plates: 575 mm Weight: 2150 kg

Ref. no.: 18092Hersteller: ENGELYear of construction: 2001Clamping unitClamping force: 300 tonOpening stroke: 855 mmPlaten size (h x v): 1050 x 650 mmInjection unitScrew diameter: 60 +35 mmInjection volume: 735 +135 cm³Shot weight: 662 + 122 gInjection pressure: 1834 +1620 barMeasurements and weightDimensions: 7,75 x 2,35 x 2,6 mMachine weight: 24780 kg

Arburg Allrounder 320S 500-60 Clamping force: 50t Year of manufacture: 09/2005 Injection weight: 27g Injection Unit .../60 Diameter of the screw: 22 mm Specific injection pressure: 2340 bar Injection volume: 30 cc Injection weight: 27 g L/D ratio of screw: 20 Tool clamping system 500/... Clamping force: 50 t Tool plate dimensions: 446 x 446 mm Distance between columns: 320 x 320 mm Tool height: 225 mm Opening travel: 350mm Maximum spacing of the plates: 575 mm Weight: 2150 kg

Ref. no.: 18368Hersteller: ARBURGYear of construction: 1997Clamping unitClamping force: 50 tonOpening stroke: 350 mmDistance between tie bars: 320 X 320 mmMould height min.: 300 mmMould height max.: 550 mmPlaten size (h x v): 446 X 446 mmInjection unitScrew diameter: 30 mmInjection volume: 85 cm³Shot weight: 75 gInjection pressure: 2200 barMeasurements and weightDimensions: 3,25 x 1.15 x 2,0 mMachine weight: 2250 kg

Arburg Allrounder 320KS 700-100 Clamping force: 70t Year of Make: 2002 Injection weight in hp: 59g Injection Unit .../100 Screw diameter: 30 mm Spec. Spray pressure: 1550 bar Spray volume: 70 cc Injection weight in hp: 59 g L/D Screw Ratio: 16.7 Clamping unit 700/... Clamping force: 70 t Size of the clamping plates: 476 x 476 mm Clearance spar spacing: 320 x 320 mm Ejector force: 30 kN Tool installation height: 200...400 mm Opening travel: 250 mm Max. plate spacing: 650 mm Ejector travel: 70 mm Weight: 2100 kg Dimensions(m) LxWxH: 3.2 x 1.5 x1.9 m Control type: Selogica

Ref. no.: 18333Hersteller: DEMAGYear of construction: 1998Clamping unitClamping force: 330 tonOpening stroke: 675 mmDistance between tie bars: 710 x 630 mmMould height min.: 330 mmMould height max.: 710 mmPlaten size (h x v): 1040 X 950 mmInjection unitScrew diameter: 50 mmInjection volume: 530 cm³Shot weight: 480 gInjection pressure: 2426 barMeasurements and weightDimensions: 6,5 X 2,0 X 2,3 mMachine weight: 14500 kg

Engel ES 330/70H Clamping force: 70t Year of Make: 2000 Injection weight in hp: 103g Injection Unit .../330 Screw diameter: 30 mm Spec. Spray pressure: 2180 bar Injection volume: 113 cc Injection weight in hp: 103 g L/D Screw Ratio: 23.6 Clamping force 70 t Size of the clamping plates: 690 x 680 mm Clearance spar spacing: 450 x 450 mm Weight: 5200 kg Control Type: EC100 tools: -Funnel -2 x hydraulic core -EUROMAP 12

Ref. no.: 17540Hersteller: ARBURGYear of construction: 1994Clamping unitClamping force: 50 tonOpening stroke: 350 mmDistance between tie bars: 270 X 270 mmMould height min.: 200 mmPlaten size (h x v): 405 X405 mmInjection unitScrew diameter: 25 mmInjection volume: 67 cm³Shot weight: 61 gInjection pressure: 2500 barMeasurements and weightDimensions: 3,3 X 1,5 X 2,0 mMachine weight: 2400 kg

Battenfeld HM 180 /525H/60V Clamping force: 180t Year of Make: 2009 Injection weight in hp: 175/20.8g Injection unit .../525/... 60 Screw diameter: 35/18 mm Spec. Spray pressure: 2743/2593 bar Injection volume: 193/22.9 cc Injection weight in hp: 175/20.8 g L/D Screw Ratio: 22/20 Clamping unit 180/... Clamping force: 180 t Lights spar spacing: 570 x 520 mm Tool installation height: 305 mm Ejector travel: 200 mm equipment: -Servo drive rotary table -3 x Hydraulic Core

Clamping force: 2000kN, tie bar spacing: 520mm/520mm, platen dimensions X/Y: 715mm/715mm, min. mold installation height: 250mm, max. opening stroke: 650mm, ejector stroke: 225mm, ejector force: 66kN. Screw diameter: 55mm, injection weight: 240g, injection pressure: 2500bar, stroke volume: 286cm³, injection unit: 675. Machine dimensions X/Y: approx. 5600mm/1700mm, weight: approx. 7000kg, operating hours: approx. 62144h. Documentation available. On-site inspection is possible. Expected to be available from June 2025.

Borche BH320 Clamping force: 320t Year of Make: 2017 Injection weight in hp: 771g Screw diameter: 60 mm Spec. Spray pressure: 1560 bar Injection volume: 848 cc Injection weight in hp: 771 g Cylinder heating capacity: 18.6 kW Clamping unit 320/... Clamping force: 320 t Size of the clamping plates: 960 x 960 mm Lights spar spacing: 665 x 665 mm Ejector force: 77 kN Tool installation height: 220...655 mm Opening travel: 580 mm Max. plate spacing: 1235 mm Ejector travel: 180 mm Weight: 12000 kg Dimensions(m) LxWxH: 7.0 x 1.8 x 2.4 m Control type: KEBA 1075

Flange diameter: 160mm, clamping force: 1600kN, tie bar distance: 520mm/520mm, min. mold diameter: 350mm, min. mold installation height: 300mm, opening stroke: 650mm, platen distance: 950mm, ejector stroke: 150mm. Screw diameter: 45mm, injection pressure: 2336bar, stroke volume: 318cm³, nozzle radius: 15mm, injection volume: 134cm³, injection weight: 289g. Machine dimensions X/Y/Z: approx. 4900mm/1600mm/2200mm, weight: approx. 7400kg, operating hours: approx. 71187h. The machine has an unknown defect. Documentation available. An on-site inspection is possible.

B&A REF: 9169 TON: 250 SCREW DIAMETER: 60MM SHOT WEIGHT: 800 STROKE VOLUME: 880CM3 INJECTION PRESSURE: 1840AR PLATEN SIZES: 900 X 790MM DBTB: 630 X 530MM MIN MOULD HEIGHT: 200MM MAX MOULD HEIGHT: 650MM MOULD OPENING STROKE: 550MM MAX DAYLIGHT: 1200MM EJECTOR STROKE: 200MM CONTROLS: TACTUS CORE PULLING: 2 AIR VALVES: 2 MOTOR: SERVO HEATING CAPACITY: 27KW ROBOT INTERFACE: EUROMAP 67 SCREW MOTOR DRIVE: HYDRAULIC

Clamping force: 500kN, tie-bar spacing: 304mm/304mm, platen size X/Y/: 480mm/480mm, min. mold height: 150mm, max. opening stroke: 525mm, opening stroke: 375mm. Screw diameter: 35mm, injection volume: 134 cm³, injection pressure: 1485bar. Dimensions X/Y/Z: approx. 3300mm/1300mm/1900mm, weight: approx. 2500kg. On-site inspection is possible.

B&A REF: 9149 TON: 850 SCREW DIAMETER: 110MM SHOT WEIGHT: 4320 STROKE VOLUME: 4750CM3 INJECTION PRESSURE: 1400AR PLATEN SIZES: 1670 X 1580MM DBTB: 1140 X 1020MM MIN MOULD HEIGHT: 400MM MAX MOULD HEIGHT: 1100MM MOULD OPENING STROKE: 1200MM MAX DAYLIGHT: 2300MM EJECTOR STROKE: 400MM CONTROLS: DIMI EL2 PLUS CORE PULLING: 4 AIR VALVES: 5 MOTOR: 37 + 37 HEATING CAPACITY: 37KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE: ELECTRIC

Clamping force: 1000kN, tie bar distance: 420mm/420mm, min. installation height: 250mm, max. opening stroke: 750mm, screw diameter: 40mm, injection volume: 226.5cm³, injection weight PE/PS: 206g/161g, injection pressure: 2164bar. Dimensions X/Y/Z: approx. 4500mm/1500mm/2000mm, weight: approx. 4700kg, control: Unilog 4000B, operating hours: 99295h. Including Euro package, ejector plate safety device, AK+ screw cylinder and storage cassette with 21 slots. Documentation available. On-site inspection is possible.

B&A REF: 8838 TON: 820 SCREW DIAMETER: 93MM SHOT WEIGHT: 2555 STROKE VOLUME: 2777CM3 INJECTION PRESSURE: 1478AR PLATEN SIZES: 1730 X 1560MM DBTB: 1250 X 1060MM MIN MOULD HEIGHT: 350MM MAX MOULD HEIGHT: 1100MM MOULD OPENING STROKE: 1150MM MAX DAYLIGHT: 2250MM EJECTOR STROKE: 350MM CONTROLS: SEF 2000 CORE PULLING: 3 AIR VALVES: 2 MOTOR: 93 HEATING CAPACITY: 41KW ROBOT INTERFACE: EUROMAP SCREW DRIVE: HYDRAULIC

Clamping force: 25kN, injection force: 5.7kN, screw motor: 12Nm, heating: 3.4kW.

B&A REF: 9168 TON: 180 SCREW DIAMETER: 40MM SHOT WEIGHT: 268 STROKE VOLUME: 295CM3 INJECTION PRESSURE: 2250AR PLATEN SIZES: 810 X 690MM DBTB: 570 X 460MM MIN MOULD HEIGHT: 170MM MAX MOULD HEIGHT: 550MM MOULD OPENING STROKE: 470MM MAX DAYLIGHT: 1020MM EJECTOR STROKE: 180MM CONTROLS: TACTUS CORE PULLING: 2 AIR VALVES: 2 MOTOR: SERVO HEATING CAPACITY: 13KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE: HYDRAULIC

Operating pressure: 210bar, injection force: 693kN, clamping force: 3500kN, opening stroke: 700mm, mold installation height: 600mm-950mm, power: 118kW, operating hours: 176,533h, cycles: 1,569,030. documentation available. On-site inspection is possible.

Screw diameter: 120 mm Injectable volume: 6450 cm3 Injection pressure: 1480 bar Passage between columns: 1170 x 1000 mm Robot interface 5 hydraulic cores ROBOT SEPRO

Injection pressure: 2100bar, injection volume: 595cm³, injection weight: 565g, injection speed: 299cm³/s. Clamping force: 250t, clamping force: 275t, platen dimensions X/Y: 920mm/920mm, opening stroke: 575mm, mold height min./max.: 200mm/685mm, tie bar distance: 585mm, ejector stroke: 175mm, ejector stroke: 180mm, centering: 160mm, operating hours: 62149h. Documentation available. On-site inspection is possible.