Format range: max. 1000 mm, min. 76 mm. Equipment: Longitudinal seam, folding bottom, double margin, 4+6 point gluing, Valco MCP electronic gluer with 4 application heads, Disc underglue on the left, feeder with vibrator and tooth gauge, Pre-crusher right with belt, left up to max. 30 mm, additional central transport, folding floor module A2 with additional upper and lower centre transport, additional central transport in folding station, pneumatic kicker, counter, digital position indicators, Bobst CUBE control, camera monitoring, remote control, small box device, pneumatic, extended press belt. Overhaul 2025: cleaned, checked, painted and with new feeder and transport belts.
Hot foil stamper, available now, fully workshop refurbished, ready to test • ELEVATED MACHINE Machine elevated 415 mm, included elevation of the steps • Step • Centerline for job quick change • Electronic device for sheet travel control • Air conditioning for the electrical cabinet • Gripper bars • Bobst-electronic for managing the machine • Motore principale con variatore di frequenza • Pianale porta-pila con leva per la correzione laterale manuale della pila durante la produzione • NON-STOP FEEDER MANUAL DEVICE • Adjustable lateral blowers with Centerline references • Suction unit with multiple adjusting • Safety system for lowering the pile try • Introduction table covered by antistatic steel stainless plate • Sheet synchronization adjustable during the machine is running for adapting feeder cycle to platin cycle • Feed belt slow-down device Ensures ...
Format range: Max. 1100 mm Min. 126 mm Equipment: Longitudinal seam, folding bottom, double margin, 4 + 6 point gluing, electronic gluer HHS X-tend ² with 6 application heads, Disc subglue unit on the left, mechanical overhaul folding with Cycle / chain alignment, vibrator with blowing air at the feeder, dental gauge at the feeder, additional central transport in the primary crusher, primary crusher right and left, kicker, counter, additional central transport in folding, Dünki silicone belt dispenser, pneumatic, intermittent press belt, overhauled in 2019.
Reference ID PP-47933 Category Flexo Printer Manufacturer Bobst Model 160 A-Matic and Flexo 160 Year Built 1994 Color 2 Impression- Working Hours - Speed 6500 sheets/h Max. size 1,600 x 1,100 mm Min. size 600 x 520 mm Condition Good Location Europe Availability - Machine Description BOBST 160 A-MATIC CUTTING MACHINE Sheet sizes: - Maximum cutting size: 1,600 x 1,100 mm - Minimum cutting size: 600 x 520 mm Cutting size with front waste: - Maximum cutting size: 1,600 x 1,075 mm - Minimum cutting size: 580 x 492 mm - Gripper margin adjustable: 15 +/- 3 mm - Thickness of corrugated board up to 9mm - Thickness of solid board from 1mm - Cutting force, maximum: (400 tons) 4MN - Production speed: up to 6.500 sheets per hour Construction year: 1994 Production country: SWITZERLAND Voltage: 480 V Frequency: 50 Hz 2 COLORS UNIT BOBST FLEXO 160 Sheet sizes: - Maximum ...
Reference ID PP-48048 Category Flexo Printer Manufacturer Bobst Model F&K 20SIX S Year Built 2015 Color 8 Impression- Working Hours - Speed 350 m/min Max. size 800x1300 mm Min. size 320x650 mm Condition Good Location Europe Availability Immediately
Reference ID PP-47933 Category Flexo Printer Manufacturer Bobst Model 160 A-Matic and Flexo 160 Year Built 1994 Color 2 Speed 6500 sheets/h Max. size 1,600 x 1,100 mm Min. size 600 x 520 mm Condition Good Location Europe Availability - Machine Description BOBST 160 A-MATIC CUTTING MACHINE Sheet sizes: - Maximum cutting size: 1,600 x 1,100 mm - Minimum cutting size: 600 x 520 mm Cutting size with front waste: - Maximum cutting size: 1,600 x 1,075 mm - Minimum cutting size: 580 x 492 mm - Gripper margin adjustable: 15 +/- 3 mm - Thickness of corrugated board up to 9mm - Thickness of solid board from 1mm - Cutting force, maximum: (400 tons) 4MN - Production speed: up to 6.500 sheets per hour Construction year: 1994 Production country: SWITZERLAND Voltage: 480 V Frequency: 50 Hz 2 COLORS UNIT BOBST FLEXO 160 Sheet sizes: - Maximum cutting size: 1,600 x 1, ...
Completely overhauled ready for testing Machine Electronic device for sheet travel control Air conditioning for the electrical cabinet Gripper bars C.U.B.E. Bobst-electronic for managing the machine C.U.B.E. Bobst-electronic for managing the complementary equipment BM Main motor Feeder Pile-tray with handle allowing manual lateral correction of the pile during production SPECIAL SHEET BREAKER DEVICE. To push the sheets downwards, ensuring good stacking NON-STOP FEEDER MANUAL DEVICE Adjustable lateral blowers with Centerline references Suction unit with multiple adjusting Safety system for lowering the pile try KERSTEN ANTISTATIC DEVICE ON THE SHEET FEEDER FOR SHEET TRAVEL Introduction table Covered by antistatic steel stainless plate Sheet synchronization adjustable during the machine is running for adapting feeder cycle to platin cycle 4 front lays, adjustable in p ...
used
Format range: Boxes, folded flat: max. 400 mm, min. 50 mm Length of the boxes: max. 500 mm, min. 100 mm Equipment: Standard, left-hand delivery, self-drive in the rotary module, vibrator, self-drive in the delivery, with packing table, processable materials: solid board, E-flute, box types: ordinary folding boxes 4+6 dot boxes, with or without lid. Overhaul 2025: cleaned, checked, painted, new belts.
Format range: max. 1100 mm, min. 66mm. Equipment: Longitudinal seam, folding bottom, double edge, 4+6 point gluing, electronic HHS X-tend³ top gluing unit, 8 channel with 6 application heads, equipped with the following additional modules for quality assurance: code reader / disc glue control / nozzle glue control / linear ejector control, disc bottom gluing unit left, feeder with vibrator, tooth gauge and vacuum, cutting alignment to the right and left after the feeder, pre-crushing module with central transport, new electronic servo overhaul folding (Stöber) with Touchscreen and program memory, new radio remote control, digital position indicators, motorized format adjustment, central transport in the folding, 2x motorized elevating tool holders, pressing device after folding, kicker, counter, camera monitoring of the transfer station, 2x box aligner on the press belt, completel ...
Bobst Flexo 200 5 colours flexo printing machine for corrugated board 5 flexo printing units Prefeeder Automatic Delivery Machine is in a very good condition Available immediately Location: Western Europe Manufacturer: Bobst SA Switzerland Type: Flexo 200 Year of manufacturing: 1988 Max. Sheet size: 1270 x 2032 mm Min Sheet size: min. 600 x 520 mm Max. printing area: max. 2032 x 1270 mm Material thickness max. : 9 mm
Format range: max. 680 mm min. 126 mm Equipment: Longitudinal seam, disc underglue unit left, Vibrator & dental gauge on the feeder, Bobst CUBE control, primary crusher right and left, kicker, counter, fully automatic format setting with program memory, pneumatic, intermittent press belt. Overhauled 2022: cleaned, checked, painted, new jetty and Transport belts.
- max. open blank width 1000 mm - straigt line - automatic crash lock bottom - REUTHER gluing system with guns - machine in production
Format range: max. 750mm, min. 66mm. Equipment: Longitudinal seam, folding bottom, double edge, motorized format adjustment, electronic top gluer Robatec, 8 channel with 6 application heads, feeder with vibrator and self-drive, vacuum at the feeder, dental gauge, quick feeder belt adjustment, video surveillance at the handover, cutting alignment according to the feeder right and left, HHS Xtend² quality assurance system with code reader pane underglue control, disc subglue unit left with fully automatic HHS pump-up glue unit and Level control, mechanical disc top gluing unit with 2 stations, Pre-crusher right and left, kicker, counter, Bobst CUBE control, digital Position indicators, motorized additional station for folding tool, middle station in folding, additional upper middle station in folding, pressing device right/left after folding, rejection by Bobst flipper in the trans ...
Format range: max. 750mm, min. 66mm. Equipment: Longitudinal seam, folding bottom, double edge, motorized format adjustment, electronic top gluer Robatec, 8 channel with 6 application heads, feeder with vibrator and self-drive, vacuum at the feeder, dental gauge, quick feeder belt adjustment, video surveillance at the handover, cutting alignment according to the feeder right and left, HHS Xtend² quality assurance system with code reader pane underglue control, disc subglue unit left with fully automatic HHS pump-up glue unit and Level control, mechanical disc top gluing unit with 2 stations, Pre-crusher right and left, kicker, counter, Bobst CUBE control, digital Position indicators, motorized additional station for folding tool, middle station in folding, additional upper middle station in folding, pressing device right/left after folding, rejection by Bobst flipper in the trans ...
Printed circuit board 734 QI (PCB) / control PC with integrated touch display on the insert, for Bobst Alpina 110 II matic. PCB Printed circuit boards 734 QI / control PC with integrated touch display on the feeder, for Bobst Alpina 110 II matic. Manufacturer numbers and replacement numbers: BSA07230000BW / BSA07230000BT / BSA07340000TH
Control Card / Plug-in Circuit / PCB Board for Bobst Alpina 110 II matic. Control card / plug-in circuit / PCB board for Bobst Alpina 110 II matic. BSA0701239601
Bobst Cube / monitor with control unit for transfer station, Bobst Alpina 110 II matic. Used and tested. Bobst cube / monitor with control unit for transfer station, Bobst Alpina 100 II matic. Used and tested. BSA07320000TG / H12P+P50S1
Details Name Bobst Media 45 ID PP-44292 Category Folder Gluer Manufacturer Bobst Model Media 45 Year 1991 Max. size 70x450 mm Condition Good Location Europe Availability Immediately Description • possibility of linear gluing from a wheel, • min. input width 70 mm, • Maximum 450 mm.
Format range: max. 1100 mm min. 76 mm Equipment: Longitudinal seam, folding bottom, double margin, 4+6 point gluing, digital positioning system for format adjustment with 5000 memory locations, feeder with its own servo drive, 2x vacuum belts, tooth gauge and vibrator, new cutting alignment station right and left after the feeder with 2 additional central supports, primary crusher right with 43 mm belt / left up to 30 mm, additional center transport, vacuum adjustment, new servo overhaul folding Stöber, folding floor module with additional upper and lower Central transport, electronic top gluer HHS Xpect, 8 channel with 5 application heads, disc bottom gluing unit on the left, additional central transport in folding station, Bobst C.U.B.E, pneumatic kicker, digital position indicators, camera monitoring, remote control, small box device, mailing bag device, cutting alignment stati ...
Format range: Boxes, folded flat: max. 400 mm, min. 50 mm Length of the boxes: max. 500 mm, min. 100 mm Equipment: Standard, right-hand delivery, own drive in the rotary module, vibrator, own drive in the delivery, infinitely adjustable via potentiometer, standalone solution via speedometer, processable materials: solid board, E-flute, carton types: Ordinary folding boxes 4+6 dot boxes, with or without lids. Overhaul 2024: cleaned, checked, painted, new belts and belts.
Reference ID PP-42880 Category Flatbed Die Cutter Manufacturer Bobst Model SPrintera 106 PER Year Built 2003 Color- Impression- Working Hours - Speed 12000 sheets/h Max. size 106 x 76 cm Condition Good Location Europe Availability December 2024 Machine Description Paper : min. 70 g/m2 Solid board (depending on the quality) : up to 2000 g/m2 Corrugated board (depending on the quality) : up to 4 mm Non Stop feeder and delivery 2x Stripping Powder register is new 2024 New controls Fully automatic feeders Semi-automatic delivery units
The machine was converted for a labeling process. The delivery or the pressing belt runs 90° to the left. The machine is still in production. The machine will be sold without labeling system. We offer a converted gluing machine without gluing system.
AUTOMATIC DIE CUTTER BOBST SP 1260 E - Year 1965, Totally rebuilt in 2008, Stripping device - Max size 126x92 cms., Min. size 35x50 cms. - Pressure max 500 tons, 4.500 sh/hour - Chases and frames, Manuals and all accessories -Available immediately, in production, any test possible
Format Range: max. 1000 mm min. 126 mm Equipment: Longitudinal seam, folding bottom, double edge, 4 point gluing, electronic gluing unit HHS, 4 channel with 2 application heads, Disc gluing unit left, feeder with vibrator, Primary crusher right and left, lower central transport in primary crushing station, new electronic overtaking fold (rummage) with touch screen and Order memory, folding floor extension module A2 with lower Central transport, kickers, counters, digital position displays, Bobst CUBE control, additional center feed top/bottom in folding, cutting alignment on the press belt, pneumatic, clocked press belt. Overhaul 2024: cleaned, tested, painted and with new feeder and transport belts, as well as equipped with new pressing belts. Other: The machine can be viewed while it is running by arrangement.
Bobst Media 68 II A2 Age: 1989 Format max.: 60 x 68 cm Min. size: 6 x 12.6 cm Material: Cardboard 100-600 g/m2 or Corrugated board N-F and E-Flutes Bottom Glueing Unit for longitudinal gluing Pressing station Tünkers FAS 480 Delivery packing system Optional: HHS-Glueing System with 3x Glueing Guns
Automatic Carton Folder Gluer For Processing Straight Line, Crash Lock, 4 Corners Style Cartons, Max. Open Blank Width: 1000mm, Min. Open Blank Width: 56mm, Max Feed Up Length: 600mm, Min. Feed Up Length: 60mm, Convertible Stock Solid 100-600 g/m2, Corrugated Upto E Flute, Operating Speed 20 - 300 m/min., Complete with: - Bottom Belt Friction Feeder, - Pre Fold, - Servo Driven Back Lifter, - HHS Xtrend Glue System with 3 Guns, - Double Trombone with Kicker, - Compression Belt Delivery
Reference ID PP-40722 Category Folder Gluer Manufacturer Bobst Model Domino 110-M II Matic Year Built 1996 Color- Impression- Working Hours - Speed-- Max. Size 1100 mm Min. Size 126 mm Condition Good Location Europe Availability Immediately Machine Description Machine equipped with Auto Bottom / 4 Corners / 6 Corners. with Handypack (right outlet) and HHS 6 gun adhesive system.
Format Range: max. 1000 mm min. 126 mm Equipment: Longitudinal seam, folding bottom, double edge, 4-point gluing, electronic gluing unit HHS, 8 channel with 2 application heads, Disc gluing unit left, new electronic overhaul folding with servo motors, 4-point control with touch screen and Order memory, feeder with vibrator & dentistry, Folding floor module A2 with central transport, primary crusher right and left, Kicker, counter, Bobst CUBE control, digital position indicators, pneumatic, clocked press belt. Overhaul 2024: cleaned, tested, painted and equipped with new and conveyor belts. Other: The machine can be viewed while it is running by arrangement.
Reference ID PP-40051 Category: Flatbed Die Cutter Manufacturer Bobst Model SP 142-ER Year Built 1986 Color- Impression- Working Hours - Speed-- Max. Size 1020x1420 mm Min. Size 500x700 mm Condition Good Location Europe Availability Immediately Machine Description vacuum feeder The Cut Station Stripping station
