used MAE for sale

Automatic straightener, shaft straightener , MAE -25RH, 1996, used Manufacturer: Maschinen- & Apparatebau Götzen GmbH, Germany Connected load: 14.5kva , Dim.: 2.5 x 1.5 x 1.8m, Weight : 5000kg

Automatic straightener, shaft straightener , MAE -25RH, 1996, used Manufacturer: Maschinen- & Apparatebau Götzen GmbH, Germany Connected load: 14.5kva , Dim.: 2.5 x 1.5 x 1.8m, Weight : 5000kg

Automatic straightener, shaft straightener , MAE -25RH, 1996, used Manufacturer: Maschinen- & Apparatebau Götzen GmbH, Germany Connected load: 14.5kva , Dim.: 2.5 x 1.5 x 1.8m, Weight : 5000kg

pressure: 40 t throat: 320 mm stroke: 250 mm arm length: 320 mm table surface area: 1400x600 mm ram surface: 1200x600 mm dayligth: 650 mm total power requirement: 22 kW weight of the machine ca.: 8 t dimensions of the machine ca.: 3200x3300x3300 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pressing force: 10t, oil filling: 300l, max. pressure: 20bar, press type: C-column press, machine dimensions X/Y/Z: approx. 1250mm/1200mm/3000mm. On-site inspection is possible.

Press capacity: 40 ton Daylight: 550 mm Stroke: 150 mm Ram speed down: 50 mm / sec Ram speed up: 85 mm / sec Throat depth: 250 mm Table surface area: 1.400 - 4.900 x 280 mm mm Table height over floor: 900 mm Oil volume: 250 l Driving motor: 5,5 kW Dimensions L x W x H: 1.400 x 1.800 x 2.400 mm Weight of machine approx.: 2.300 kg

pressure:6 t stroke:1020 mm total power requirement:3,5 kW Can only adjust between tips

Single column hydraulic press MAE type S63SZ SOMasch.Nr. 551277 year of construction approx. 1977Compressive force 63 ton. Projection 320 mmTable surface 850 x 630 mmPlunger area 1050 x 500 mmPlunger stroke 500 mmInstallation height max. approx. 730 mmTable height above floor 970 mmTank capacity hydraulics 600 litresDrive power 15 kWNex connection 380 Volts, 50 Hz- Hydraulic cushion under the table with holes through the table top- 2-hand control- Electric control cabinet damagedSpace requirement L x W x H 2000 x 1200 x 3420 mmWeight approx. 5

Stander - hydraulic press MAE type S63SZ SO Masch.Nr. 551277 year of construction approx. 1977 compressive force 63 ton. Projection 320 mm Table surface 850 x 630 mm Plunger area 1050 x 500 mm Plunger stroke 500 mm Installation height max. approx. 730 mm Table height above floor 970 mm Tank capacity Hydraulics 600 liters Drive power 15 kW Mains connection 380 Volts, 50 Hz - Hydraulic drawing cushion under the table with holes through the table top - 2-hand control - Electric control cabinet damaged Space requirement L x W x H 2000 x 1200 x 3420 mm Weight approx. 5 ton. The machine is working, but the control cabinet is mechanically damaged. During the test run, the machine reaches a pressing force of 50 tons, presumably a pressure relief valve flows out. used