used REITZ for sale

Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 60060060mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.

Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 60060060mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.

REITZ RW40300400 agitator for tank containers 4.0 KW / 300 rpm and inclined blade stirrer Worm gear motor IE3: Three-phase motor Moll 3 x 230/400 Volt, 4.0kW, IP55, n1 = 1440 rpm, n2 = 300 rpm, worm gear, i = 1:5, plug-in shaft as output shaft D = 28 mm. 5 m cable and motor protection plug. Shaft: Precision stainless steel shaft D30, length 2000 mm, diameter 30 mm, Material: stainless steel. With 2 x 1000 mm pitch and additional rigid coupling. Coupling: 2 pieces rigid coupling, 1x 28/30, 1x 30/30 mm, material stainless steel Agitator: 2 pieces of double-bladed oblique blade stirrers, diameter 400 mm, material stainless steel 1.4571, welded version. Truss: With 1 piece mounting frame approx. 400 mm x 2600 mm Each longitudinal strut 2600 mm consists of 2 mounting rails 41 x 82 mm profile. With diagonal struts and angles for fixation on tank frames. Frequenc ...

Manual Heating Press Reitz MHSP5H - Manual Lifting Screw Press Static Press Force 5 KN (0.5 to) - Portable press frame made of polyamide PA 6G - Manual screw jack with spindle 20 mm, pitch 5 mm - With handwheel diameter 120 mm and handle - Gear reduction ratio 1 : 10, 0.5 mm spindle travel per handwheel revolution, thus only very little hand force required for high pressure. - Table size 100150mm - Clear width 60 mm - Punch size diameter 70 mm with 4 holes 8 mm to attach the Hotplate - Very easy operation due to spindle and worm gear - Total weight approx. 25 kg With 2 electric aluminum heating plates 1200 watts, heating area approx. 150 100 mm to 250°C, connection 230 V. With sensor and temperature control. Pressure-resistant insulating panels at the top and bottom for use in presses. Suitable for pressing, welding and gluing.

Foldable mechanical heating press with pressing surface approx. 150250mm. Stable press frame made of generously dimensioned aluminium plates and steel joints. Closure of the press plate and heating plate with ratchet. 2 pre-tensioning beams for locking hinges by means of eccentric clamps. With electric aluminum heating plate 400 watts, 1.74 A, heating area approx. 150 250 mm to 250°C, connection 230 V. With sensor and temperature control. Pressure-resistant insulating plate for use in presses. Suitable for pressing, welding transport belts and plastic straps.

Stirring tank REITZ RB300LRW037250 Stainless steel tank 300 liters with agitator 0.37 KW, used gear motor KEB 30 rpm. Stainless steel stirring tank 300 liters with outlet tap 3/4-inch. Diameter 630 mm, container height 990 mm. Tripod height 425 mm. Gear motor: Used gear motor KEB, 3 x 230/400 volts, 0.37 kW, n1 = 1350 rpm, n2 = approx. 30 rpm. With motor protection switch. Shaft: Precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, material stainless steel 1.4301. With rigid coupling 28/20 in stainless steel 1.4571. Stirring organ: Four-bladed inclined blade stirrer, diameter 275 mm, material stainless steel 1.4571. Very slow-running, high-torque agitator.

Laboratory heating press REITZ EHSP5H – used demonstration machine Heating press with pressing pressure 5 KN (0.5 tons) With heating device up to 200 °C from above and below. - Electric screw press press press force 5 KN (0.5 to) - Screw jack with spindle 20 mm, pitch 5 mm - Gear reduction ratio 1 : 10, 0.5 mm spindle travel per revolution - Clear width approx. 60 mm - Pressing area 100150mm - Heating device with temperature control, 2 heating plates 100 x 150 mm - With TECO electric motor 0.18 KW - With reversing contactor control (up – down buttons) and emergency stop - Motor protection plug against overload, with main switch - Machine table made of aluminum profiles and multiplex plate 700 700 mm - Total weight approx. 100 kg . Suitable for foil bonding and embossing. Due to self-locking of the spindle, long holding time with constant pressure. The scr ...

Used ATEX agitator RW0252800300 – 0.25 KW – 2800 rpm. For smaller containers and drums. ATEX II 2G EEx e II T3 Electric motor: Electric motor VEM motors Thurm GmbH, 0.25 KW, 2-pole, 3 x 230/400 volts, 2800 rpm, IP55. Weight approx. 8 kg. With motor protection plug. Iso F, suitable for frequency converters. Shaft: Precision stainless steel shaft D10, length 500mm, diameter 10mm, Material: Stainless steel 1.4301. With rigid coupling stainless steel 1.4571. Agitator: Double-bladed inclined blade stirrer, diameter 244mm, Material: Stainless steel 1.4571 With PTB-ATEX test certificate.

Laboratory Heating Press EHSP20H – Used Demonstration Machine Table press / electric screw press with pressing pressure 20 KN (2 tons) With heating device up to 200 °C from above and below. Press drive with screw jack gear, reduction ratio 1 : 12, spindle diameter 32 mm, Pitch 6 mm, pressing area approx. 100 150 mm, clear height and stroke approx. 300 mm. Geared motor 0.37 KW, 1,390 rpm, 4-pole, with spur gear i = 1 : 5, Speed 150 mm / min. Max. dynamic load 20 kN. With reversing control, control box and motor protection plug. Sturdy press frame made of steel. Undertable made of high-quality aluminium profiles 4545 mm, table surface 600600 mm, Table top made of multiplex board. Total weight approx. 100 kg. The table press has a pressing pressure of 20 kN (dynamic load). Typical applications are pressing work with exact lining. Suitable for pressing bonding, embo ...

Centrifugal fan REITZ type: MAE 031-007130-00Fabr. No. 601475 year of construction 2017Volume flow 4260 m³/h = 71 m³/min. Pressure p 1.2 kg/m³Air inlet 250 mm (nozzle diameter in the base plate)Air outlet 245 x 195 mmMotor speed 2915 rpm. Motor power 7.5 kWNetz connection 400 Volt 50 Hz- fan wheel with 9 fan blades- directly flanged drive motor- flange dimensions for air outlet 310 x 260 mm- stable metal housing made of 5 and 6 mm steelSpace requirement L x W x H 1390 x 1030 x 600

Centrifugal fan REITZ type MAE 045-017030-00Fabr. No. 601438 year of construction 2017Volume flow 10200 m³/h = 170 m³/min. Pressure p 1.2 kg/m³Air inlet 300 mm (nozzle diameter in the base plate)Air outlet 345 x 345 mmEngine speed 2940 rpm. Motor power 18.5 kWNet connection 400 Volt 50 Hz- fan wheel with 8 fan blades- directly flanged drive motor- flange dimensions for air outlet 450 x 450 mm- stable metal housing made of 8 mm steelSpace requirement L x W x H 1930 x 1240 x 950 mmWeight

Centrifugal fan REITZ Type: MAE 031-007130-00 Fabr. No. 601475 year of construction 2017 Volume flow 4260 m³/h = 71 m³/min. Pressure p 1.2 kg/m³ Air inlet 250 mm (nozzle diameter in the base plate)Air outlet 245 x 195 mm Motor speed 2915 rpm. Motor power 7.5 kW mains connection 400 Volt 50 Hz - fan wheel with 9 fan blades - directly flanged drive motor - flange dimensions for air outlet 310 x 260 mm - stable metal housing made of 5 and 6 mm steel space requirement L x W x H 1390 x 1030 x 600 mm Weight centrifugal fan 200 kg very good condition, only test run completed; used

Centrifugal fan REITZ type MAE 045-017030-00 Fabr. No. 601438 year of construction 2017 Volume flow 10200 m³/h = 170 m³/min. Pressure p 1.2 kg/m³ Air inlet 300 mm (nozzle diameter in the base plate)Air outlet 345 x 345 mm Motor speed 2940 rpm. Motor power 18.5 kW mains connection 400 Volt 50 Hz - fan wheel with 8 fan blades - directly flanged drive motor - flange dimensions for air outlet 450 x 450 mm - stable metal housing made of 8 mm steel space requirement L x W x H 1930 x 1240 x 950 mm Weight centrifugal fan 500 kg very good condition, only test run completed; used