We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
The Klingelnberg PSR 500 U worm gear testing machine was designed as a universal machine for the flexible testing of worm gears and is used by manufacturers of gear and gear technologies for the process of single-flank rolling testing for worm gear sets EFWP. Technical data Max. worm wheel diameter: 500 mm Max. spindle length: 500 mm Max. spindle diameter: 200 mm Center distance: 0 ... 400 mm Max. measuring speed: 60 rpm Braking torque: 2.5 Nm Max. worm wheel weight: 150 kg Max. spindle weight: 50 kg Table diameter: 300 mm Machine weight: 800 kg Dimensions: 1500 x 1500 x 1600 mm The following parameters can be measured here: • Single-flank deviations Fi', fi', fl', fk' • Crossing, concentricity, roundness (option) • Carrying pattern with digital camera • Pitch deviation • FFT analysis, spectrum Picture shows the machine in its current ACTUAL condit ...
The Klingelnberg GKP 90 bevel gear testing machine was designed as a universal machine and is used by manufacturers of gears and transmission technologies, for the process of noise and contact pattern tests on bevel gears and hypoid gears. Technical data Diameter: 540 (400) mm Hypoid: ±50 mm mm Pinion spindle Dm: 90 mm mm Dimensions: 1,800 x 1,800 x 1,600 m Machine weight: approx. 2,800 kg Information and data are non-binding, subject to prior sale Special features: The machine is intended for noise and contact pattern tests on bevel and hypoid gears of all gears. By simulating operating conditions, applying different speeds and changing the load states for drive and outlet, the optimal installation distance for standstill can be determined. Digital actual value display for 2 axes Stepless speed adjustment via frequency converter Electrically fused and acceptable ...
The Klingelnberg PEK 300 H bevel gear testing machine is designed for universal single-flank rolling testing of bevel gears and crown gears. Here, gears can be measured and graphically evaluated by means of single-flank rolling testing. These test methods are particularly suitable for determining defects in the gear geometry such as concentricity and axial running properties, rolling deviations or pitch errors. Here, a practical installation situation of a gear outside the gearbox is simulated under real load conditions and then evaluated. Deviations in the gear geometry, machining errors due to defective tools and damage to the gears can thus be detected and eliminated even before assembly. The following parameters can be measured here: » Single-flank deviations Fi', fi', fl', fk' » Crossing, Runout Roundness (Option) » Carrying diagram with digital camera » Pit ...
Klingelnberg ZW 301 Gear Measuring Machine Weight 750 kg
A gear cutter grinding machine for sharpening tools is available. max. outside diameter with helical/straight flutes: 300mm/300mm, min. cutter diameter: 60mm, max. flute grinding depth: 50mm, max. pitch angle: 45°, number of flutes: 3-45, max. grinding slide travel: 475mm, grinding wheel diameter min./max. Pitch angle: 45°, number of flutes: 3-45, max. grinding slide path: 475mm, grinding wheel diameter min./max.: 150mm/250mm, grinding spindle speed: 16m/min, speed: 2700rpm, workpiece holder: ISO40. Documentation available. An on-site inspection is possible.
A modernized Klingelnberg SNC 31 CNC 6-Axis Tool Grinding Machine. Modernizations: new belt drives, new flanges, new servo motors and new couplings in all axes. Hydraulics: new drive pump, new motor, new hydraulic hoses, original lubricant pump. Installation of a new control cabin with CNC (Siemens 840D sl) and new electrical construction (VDE). Detailed information about the modernization on request. With filter system and CO2 extinguishing system (Dangelmaier). On-site inspection is possible.
Max. workpiece diameter: 10-350mm, max. grinding length: 600mm, clamping length: 1055mm, swivel angle: +/-60°, with oil mist filtration, an inspection is possible.
Workpiece diameter: 10-350mm, max. grinding length: 660mm, clamping length: 1055mm, max. module: 25mm, swivel angle: +/-60°, grinding wheel dimensions: 300-500x100mm, with Faudi cooling lubricant belt filter and Elbaron oil mist separator. No longer fit for operation and can only be used as a basis for a complete overhaul.
Center width: 400-800mm, rotational speed: 1000-2700/min, workpiece diameter: 10-300mm, grinding wheel diameter: 40-300mm, swivel angle: -45 to 45°, length: 3000mm, width: 2500mm, height: 2275mm, with oil mist separation system Hoffmann (new filter inserts), filter system gravity belt filter Faudi, hydraulic unit, additional grinding head for grinding worm gears, grinding mandrels diameter 50, 40, 27, 22, holder for SK40 and MK5, driver sets for different clamping diameters, operating instructions, circuit diagrams in paper form, an inspection is possible.
max. wheel diameter: 540 mm turning speeds: 315 - 1260 U/min axis adjustment +/-: 50 mm ratio: 1 : 1 bis 1 : 10 taper MK: weight of the machine ca.: 2,3 t dimensions of the machine ca.: 1,7 x 2,1 x 1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: --- mm gear width: --- mm max. module: --- min. module: --- Control: --- total power requirement: --- kW weight of the machine ca.: --- t dimensions of the machine ca.: --- m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 0-200 mm max. module: 25 min. module: 0,5 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Diameter: 400 mm Klingelnberg - AFK 151 Spiral bevel gear cuting machine Ø 400 x Mod 6 MACH - ID 6237 Make: Klingelnberg Type: AFK 151 YOP: 1960 Max. Diameter 400 Ø Modu l6 mm Dimensions Length 3.000 mm Width 2.200 mm Height 2.000 mm Weight 6.900 kg
external diameter: 113 mm bore diameter in mm: 32 mm width: 130 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
external diameter: 118 mm bore diameter in mm: 40 mm width: 157 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
external diameter: 112 mm bore diameter in mm: 32 mm width: 130 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
external diameter: 106 mm bore diameter in mm: 32 mm width: 108 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
external diameter: 88 mm bore diameter in mm: 27 mm width: 91 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
external diameter: 111 mm bore diameter in mm: 32 mm width: 130 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
external diameter: 108 mm bore diameter in mm: 32 mm width: 140 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 275 mm gear width: 55 mm max. module: 6 min. module: 1,5 control: Sinumerik 840C tooth width: 5,5 mm spiral angle: 0/60 ° max. number of teeth: 120 min. number of teeth: 5 transmission ratio max.: 1:10 transmission ratio min.: 1:1 spindle speeds: max. 110 mm blade head turning speeds: 20-110 1/min total power requirement: 100 kW weight of the machine ca.: 16700 kg dimensions of the machine ca.: 5200x2300x2400 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
external diameter: 128 mm bore diameter in mm: 40 mm width: 130 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
external diameter: 103 mm bore diameter in mm: 32 mm width: 108 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 275 mm gear width: 55 mm max. module: 6 min. module: 1 Control: 840 C Siemens total power requirement: 100 kW weight of the machine ca.: 16,7 t dimensions of the machine ca.: 5,2 x 2,3 x 2,4 m m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.