Table milling machine Kölle Milling machine and circular saw combined Type FK 5 Machine No. 462 With feed ELU With 30 mm and 40 mm milling spindle With sliding table Motor power tiller 3 kW Milling shaft speed 2800/4500/6000/10000 rpm. Spindle left and right rotation Table size 1400 mm x 920 mm Table opening minimum 70 mm – maximum 390 mm Milling spindle 30 mm with clamping length 130 mm Milling spindle 40 mm with clamping length 140 mm Feed ELU with 3 rollers Saw motor power 1.5 kW Saw blade spindle diameter 30 mm Speed 3300 rpm. Saw blade diameter maximum 350 mm Cutting height maximum 105 mm Sliding table support 1100 mm x 450 mm Extraction connection diameter 2 x 120 mm Weight 1050 kg with pallet Dimensions for shipping 1 pallet with sliding table 2700 mm x 800 mm x H 1000 mm 1 pallet with machine 1600 mm x 900 mm x H 1800 mm
Key data: 500 mm, 2800 mm, 4 St.
Dresser Kölle Surface planing machine Type AH 50 Machine No. 137 Year of manufacture 1985 Planing width 500 mm Maximum cutting depth 8 mm Dressing tables 1450 mm + 1270 mm Dressing stop 1100 mm x 150 mm Swivelling dressing stop Motor power 5.5 kW Engine slightly slowed down 4 Knife Shaft Strip planer knife Serrated table lips for noise reduction With Kölle swing protection for planer blade shaft With spare blades With planer knife adjustment gauge Weight with pallet 650 kg Dimensions 2800 mm x 850 mm x H 1000 mm
Slotted Hole Drilling Machine Cologne With dowel grid Type L2 with 2 clamping cylinders for workpiece holding Dowel drilling device with pitch 16, 22, 25, 32 mm With frame stop system Motor power 1/1.1 kW Drilling depth 150 mm Drilling length 200 mm Maximum drilling height 120 mm Table size approx. 820 x 350 mm Drill chuck 3 – 20 mm
Key data: 500 mm, 2500 mm
Current consumption 10.5A 50Hz, voltage 400V Motor knife shaft 5.5A Planing width 500 mm Largest chip depth 8 mm Total table length 2500 mm Knife shaft D=125 mm with TERSA knives Knife shaft speed 5000 rpm Special accessory: Knife shaft cover Suvamatic
M.-No. 912, year 1995, motor power 8.6 kW, voltage 400V 50Hz, spindle 30 + 40 mm, sliding table: yes, round milling: yes, brake and emergency stop, speeds: 3000, 4000, 6000, 8000, 5000, 10000 rpm, accessories: Aigner stop,
Kölle Band Saw BSM40 - With belt sanding and welding machine Good condition, fully functional, can be viewed and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article can be viewed and tested under power before purchase in order to rule out misunderstandings. Please ask questions before purchasing to avoid confusion. If you have any general questions or would like to make an appointment for a viewing, I can be reached at any time on the telephone number below or above. Errors in the description and prior sale excepted. VAT is shown separately on my invoices. Shipping with forwarding agent.
Koelle Edge Planer Model FKF 51 Built in 1993 max material thickness 45 mm, Machine size L 304 x W 65 x H 87 cm, Joining head with carbide reversible knife mobile Weight approx. 360 kg The machine is in good condition, ready for use. Subject to changes, errors, prior sale ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system+technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone: 0041 62 966 18 32 Fax 0041 62 966 21 12
Tenon milling machine / tenon cutting and slitting machine Manufacturer: Kölle Model: Z40 Year of construction: 1992 1 x Sawing 1 x Milling
Technical details: - Spindle diameter: 400 mm - Max. diameter of milling tool: - Mechanical spindle height adjustment with analogue scale - Foldable rolling table - Rolling table travel max. 1,430 mm - Table length: 800 mm - Table width: 385 mm - with eccentric pressure apparatus - 1 x extraction nozzle milling machine, diameter 160 mm - 1 x suction nozzle saw, diameter 80 mm - Max. diameter of saw blade: 400 mm - Saw blade shaft diameter: 30 mm - 1 x saw blade QW 2020 x 400 x30 mounted - 1 x splitting wedge mounted - 2 x engine brake installed - With aliminium length stop (length 3,000 mm) Engine data milling unit: - Voltage: 400 V - Current: 15 A - Frequency: 50 Hz - Power: 7.5 kW - Speed: 2,850 rpm Engine data sawing unit: - Voltage: 400 V - Current: 4.8 A - Frequency: 50 Hz - Power: 2.2 kW - Speed: 2,760 rpm Dimensions (LxWxH): 2,000 x 1,530 x 1,61 ...
Key data: 500 mm, 2800 mm, 4 St.
Technical details: - Max. planing width: 500 mm - Maximum chip depth: 5 mm - Length of feed table: 1,300 mm - Length of the take-off table: 1,500 mm - Total length of the table: 2,800 mm - Table height: 800 mm - Max. workpiece length without support: approx. 1.5 m - Length of the joining fence (Aigner joining fence with integrated auxiliary fence): 1,300 mm - Height of the joining stop: 150 mm - Joining stop adjustable up to 45° and extendable over the entire width of the table - Diameter of the TERSA knife shaft: 125 mm - Nominal speed of the TERSA knife shaft: 5,000 rpm - Number of planer blades: 4 pieces - Minimum width of planer blades: 17 mm - Diameter of suction nozzle: 160 mm - Required air velocity: min. 20m/s - Required air volume: 1500 m³/h - Vacuum at 20m/s air velocity: 705 Pa - 6 x machine shoes with adjustment screws - incl. EMERGENCY STOP switch En ...
KÖLLE Z40 YOC 1983 Rated Current: 20A Milling machine: Motor power: 7.5 kW Speed: 4,000 rpm. 40 mm spindle Clamping height: approx. 190 mm Height adjustment via handwheel (travel: 80 mm) Saw: Motor power: 2.2 kW Speed: 3,000 rpm. 30 mm spindle max. saw blade diameter: 400 mm max. cutting height: 120 mm Sliding carriage eccentric. Workpiece clamping Length fence: 290cm can be swivelled on both sides (up to 45°) Suction connection: 160 + 80 mm Engine Brake Weight: approx. 700 kg Stop ruler available. Machine dimensions with folded table as shown: L: 200 cm W: 130 cm H: 161 cm Sold in ACTUAL condition and unrefurbished from carpentry dissolution. Fixed price.
Kölle thickness planer DH 63 Product name: Thickness planer Type: DH 63 Manufacturer: Kölle Machine number: 888 Year of construction: 2000 Condition: used technical details: • Planing width: 630 mm • min. planing height: 4 mm • planing height: 225 mm • Largest chip depth: 8 mm • Length of the thickness table: 1,000 mm • Shortest workpiece length: 260 mm • Diameter of the knife shaft: 125 mm • Speed of the knife shaft: 5,000 rpm • Number of planing knives: 4 pieces • Feed speeds: 4/6/12 m/min • Weight: approx. 1,020 kg • Electronic positioning control e.g. adjustment of the thickness table • Sliding roller in the table Electrical equipment: • Voltage: 400 V • Power knife shaft motor: 7.5 kW • Power feed motor: 0.75 kW • Power motor for thickness table adjustment: 0.18 kW Suction: • Diameter suction nozzle: 160 ...
Vertical band aege KOeLLE ST105, table 950/900 mm, v= 15 - 2300 m/min - table must be overhauled - see pictures
KonturfräÃ?maschine crosscut saw with sliding table Type: FK5 Second-hand machine Sled Spindle diameter 30 mm Speeds: 4 Height adjustment: Handwheel Power: 6kW Circular saw, crosscut saw Machine is fully functional. Machine is in good condition. We love to hear from you.
Koelle edge planing machine model FKF 51 is in good condition, ready to use. L x W x H = 3000 mm x 700 mm x 950 mm Weight approx. 200 kg Built in 1982 Engine No. 390 The rubber rings at the pressure rollers should be times replaced. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Manufacturer: Kölle Tischfräse, Type: F 50, Year: 1990, Control: oben, revolutions rpm: 3000/6000/9000, Length lifting spindle mm: 150, Diameter of the spindle mm: 30, Spindle travel range total mm: 120, Spindle swivel-mounted max Grad: no, Main engine kW: ca.4, Feeding speed: yes, Table extension - lenght: yes, Exhaust diameter mm: 150, Wight approx. kg: ca.900, FREE TEXT: Anschlag ausziehbar/Haffner Vorschub, Year :1990
Motor movable, height adjustment by handwheel, dowel drilling device, center stop, adjustable angle stop, travel device ---------- Technical data ---------- work table dimensions: 820x340 mm, drilling width: 210 mm, drilling depth: 155 mm, height adjustment: 120 mm, speed: 1,500 and 3,000 rpm., drill chuck: 1-20 mm, motor: 0.9/1.4 kW, dimensions (LxWxH): 830x1,200x1,350 mm, weight: 220 kg Sale in as-is condition, without technical inspection
Manufacturer: Kölle Tischfräse, Type: F 50, Year: 1990, Control: oben, revolutions rpm: 3000/6000/9000, Length lifting spindle mm: 150, Diameter of the spindle mm: 30, Spindle travel range total mm: 120, Spindle swivel-mounted max Grad: no, Main engine kW: ca.4, Feeding speed: yes, Table extension - lenght: yes, Exhaust diameter mm: 150, Wight approx. kg: ca.900, FREE TEXT: Anschlag ausziehbar/Haffner Vorschub, Year :1990
