Parallel Lathe WMW NILES type DLZ 500 IV L 1000 Between points: 1000 mm Maxi Ø on bench: 500 mm Maxi Ø over saddle: 300 mm Spindle diameter: Ø 50 mm Spindle speed: from 28 to 1400 RPM 3-jaws chuck Ø 200 mm Threadings: Metric + Whitworth Tailstock CM4 Auto Feeds transverse + longitudinal + rapid Lubricant pump Voltage: 380 V Dimensions (L x W x H): 3000 x 1400 x 1500 mm Weight: approx 2,5 T
Face plate diameter: 1.250mm Center height above foundation slab: 1,250mm Weight: 19t Power: 55Kw Max. torque on the face plate: 31,500Nm Maximum workpiece mass between centres: 16,000 kg Speed range: 2.24 – 224 rpm
Code 151295 Description Facinglathe with center Make WMW NILES Model DP 1 / S 2 Serial number 261 526 149 Year of make 1986 Max. centerheight over base plate 1250 mm Max. swing over base plate 2480 mm Max. swing in Gap 3100 mm Distance between centers 4000 mm Max. workpiece weight betw. centers 10.000 kgs Spindle bore 100 mm Movement slide ( max. ) 1000 ( + 750 ) mm crossslide 630 mm toolslide 200 mm 18 Speeds 5,6 – 280 rpm Motorpower 45 kW Total power 55 kVA Machine weight total ± 18000 kgs Accessoiries 4 chuck facingplate of Ø 1250 mm Condition Machine is in very good condition
Tip height: 1250 mm Turning diameter: 2,500 mm over bed Centre distance: 4.000 mm Support motion: 750 mm longitudinal feeds 630 mm cross feeds Face plate: Ã? 1250 mm Spindle speed: 5.6-280 RPM. Spindle bore: 100 mm Workpiece weight: 10.000 kg Equipped with: -Floor plates 4.500 x 2.200 mm -Powered tailstock -Operating instructions Country of origin: Germany Engine power: 45 kW Machine weight: 18,000 kg Machine Lxwxh: 8,000 x 4,000 x 2,100 mm
diameter:315 mm Speed:max. 2400 min. -1 weight of the machine ca.:25 kg
turning speed range: 2,24 – 224 U/min total power requirement: 55 kW weight of the machine ca.: 16 t faceplate diameter: 1250 mm - Faceplate diameter: 1,250mm - Center height above foundation plate: 1,250mm - Mass: 19t - Max. Torque on the faceplate: 31,500Nm - Largest workpiece mass between the centers: 16,000Kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
faceplate diameter: 1250 mm total power requirement: 55 kW weight of the machine ca.: 19 t - Face plate diameter: 1.250 mm - Peak height above foundation slab: 1.250 mm - Max. torque on the face plate: 31,500 Nm Largest workpiece mass between the tips: 16.000 Kg Speed range: 2.24 - 224rpm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
3- Jaw Chuck WMW NILES DHK 200x3 Outer Ø: 200 mm Flange: 155 mm Bore Ø: 60 mm Bolt circle: 175 mm Height with jaws: 125 mm Chuck number: 507 Dimensions: 200 x 200 x 125 mm
3-jaw chuck, three-jaw chuck, lathe chuck WMW NILES outer Ø: 250 mm bore Ø:80 bolt circle: 180 mm flange: 220 mm height with jaws: 110 mm 2400 rpm with cross cone & camlock D1- 8 inch (stud bolt M 16) 2 set of jaws (1x drilling, 1x rotary jaw set) 1 chuck wrench Dimensions: 250 x 250 x 195 mm
3-jaw chuck, three-jaw chuck WMW DH-B 200x3x6 ( DH-B200x3x6 ) TGL 30-2332 Outer Ø: 200 mm Bolt circle Ø : 133.5 mm Bore Ø: 54 mm Height with jaws: 140 mm used, tested ! Dimensions: 200 x 200 x 121 mm
Bezel, Luenette, Self-Centering Bezel WMW, NILES DFS 2/2 ID. NO.: 4099 0004 10 max. clamping diameter: approx. 150 mm Spare part for CNC lathe WMW, NILES DFS 2/2 ! used, tested ! Dimensions: 600 x 160 x 340 mm
3-jaw chuck, three-jaw chuck WMW DH-B 200x3x6 ( DH-B200x3x6 ) TGL 30-2332 Outer Ø: 200 mm bolt circle Ø : 133.5 mm bore Ø: 54 mm height with jaws: 140 mm used, tested ! Dimensions: 200 x 200 x 121 mm
Control Unit, Control Electronics, Numerical Control WMW, NILES TDR 100-01 ( TDR100-01 ) Input: 380 V AC 35 A 49 - 62 Hz Output: 270 V DC 25 A IP 00 New ! Dimensions: 250 x 160 x 160 mm
Control Unit, Control Electronics, Numerical Control WMW, NILES TDR 700-223 ( TDR700-223 ) Input: 380 V 3AC 41 A 49 - 62 Hz Output: 400 V DC 50 A Ersatzteil u.Ersatzteil u.a. for milling machine AUERBACH FkrSRS 250 CNC-H 646 ! used, tested ! Dimensions: 315 x 270 x 200 mm
3-jaw chuck, three-jaw chuck, lathe chuck WMW NILES outer Ø: 250 mm bore Ø:80 bolt circle: 180 mm flange: 220 mm height with jaws: 110 mm 2400 rpm with cross cone and camlock D1- 8 inch (stud M 16) 2 set of jaws (1x drill 1x rotary jaw set) 1 chuck wrench Dimensions: 250 x 250 x 195 mm
Control unit, control electronics, numerical control WMW, NILES 70.1011 1x PCB: 70.1011-13:1B/1 1x PCB: 70.1011-9:1B/1 1x PCB: 70.1011-11:1B/1 used, spare parts dispenser ! Dimensions: 250 x 160 x 160 mm
3- Jaw chuck WMW NILES DHK 200x3 Outer Ø: 200 mm Flange: 155 mm Bore Ø: 60 mm bolt circle: 175 mm Height with jaws: 125 mm feed number: 507 Dimensions: 200 x 200 x 125 mm
3-jaw chuck, three-jaw chuck, lathe chuck WMW NILES DH-B 315 x 3 x 6 outer Ø: 315 mm Bore Ø: 100 mm Height with jaws: 130 mm bolt circle: 33 / 290 mounting: M14 3 jaws extra Speed max.: 1800 rpm min. 20-240 mm max. 75-240 mm complete with inner and outer jaws Dimensions: 315 x 315 x 150 mm
centre distance: 5000 mm turning diameter over bed: 4000 mm turning dia. in gap: 5000 mm spindle bore: 104 mm turning speeds: 1,4 - 71 (18x) U/min total power requirement: 30 kW weight of the machine ca.: t dimensions of the machine ca.: m 4-jaw face plate Ø 3.150 mm modular lathe! The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
