6 spindles Tapping Slotting tool Peeling tool holder Pick-up device lots of accessories with bar feeder IEMCA PRA 40/31 P (3m - poles)
6 spindles Threading with electronic limiting Hexagonal beating Calibrate Pick-up device lots of accessories with bar feeder IEMCA PRA 40/42 F Including STEIMEL chip disposal, crate conveyor, 24/7 production
6 spindles Tapping Cross drilling Thread Rollers Milling apparatus a lot of accessories Feed motor (spindles) defective! with bar feeder IEMCA PRA 40/32 P
- 6 spindles - Max. bar clearance: 63.0 mm - Rod guide and stand including many accessories (see photos)
used
Number of spindles 8 Controller Siemens 810D Chuck diameter: 130 mm Max part diameter: 135 mm Total stroke: 125 mm Working length: 100 mm
Manufacturer: Schütte Type: ADH 160 Machine No.: 225 Year of construction: 1981 Weight: 11t General / technical data: turning length: 125mm workpiece diameter: 168mm max drilling depth: 125mm Adjustable quantity: from 3.4 to 450 sec. Operating hours: 8.200h Working spindle speed: from 90 – 1120 rpm Installation area (l x w x h): approx. 4730 x 1700 x 2120mm Power Supply: 380V / 50Hz Accessories: 7 cross slides 8 longitudinal slides Tapping device 4x 2-jaw lining Ø160mm Type of lining: Draft chuck with clamping diameter 15 Type of lining: Röhm 0W-406 682 Clamping force 1200 da N 4x 3-jaw lining Ø160mm Type of lining: Draft chuck with clamping diameter 15 Type of feed: Röhm 1W-406 681 Clamping force 1800 da N Insert arm over lining 100mm. The workpiece is fed to the insert arm by a swivel arm and rotary gripper. Rem ...
• Siemens 840 C controller • Location I + III + IV + VI: Longitudinal and transverse slide • Position II + V: CNC slide and longitudinal slide Bvxhlj3gi3 • Advance position VI • Interceptor Position VI • KS system (emulsion) • Loading magazine Cucchi model Multi-6 156C15, YOC 2015, • Ruez hinge belt conveyor in the machine bed • Hinge conveyor Knoll 280 S-1/40 ID 26565 (outside) • Electrostatic separator ISI RON/A 2500A, ID 26295 • Without further accessories / tools • CUCCHI BLT Model Multi -6 YOM 2015
Year of manufacturing: 1999 Travels: -X: 500 mm -Y: 320 mm -Z: 320 mm Center height: 320 mm Workpiece length between centers: 700 mm Table clamping area: 1210 x 116 mm Grinding spindle speed: 2250 / 3000 / 4000 / 6000 rpm Spindle motor: 2,4/3,0 kW Machine weight: 3000 kg Control: NUM 1000
Schuette Multi-spindle rotary machine Name: Schuette SF 20-6 Curve controlled Number of spindles: 6 Built: 1984 max. rod diameter: around 20 mm SW 17 mm AK 18 mm VK 14 mm max. rod feed: 80 /(160) mm Number of independent Laengsschlitten: 6 Total / working distances (stand): 63/40 mm " " (special) up to: 100/63mm Number of independent cross slides: 6 Total/ work routes Medium and top slide up to: 32/20 mm Slide up to: 40/25 mm Spindle circle diameter: 224 mm Main times min/max.: 0.36/150 sec. Off times min./max.: 0.45/0.80 sec. Spindle speed from / to: 900-5000 rpm in the 2nd area: 355-2000 rpm Rated power of the drive motor: 15 KW Connected power: 50 kVA Drive engine speed: 1500 rpm Length Width (in standard performance) 3705 1320 mm incl. rod guide (in standard output) 6335 mm Weight without rod guide a ...
Schuette multi-spindle rotary machine SF 26-6 1987 built 6-spindle rod turning machine with hydraulic catch slide prepared for Co2 Loesch plant run with cutting oel Schuetz control mechanical gearbox separate hydraulic unit -- Pick-up device with hydraulic voltage and back-weighing machining without Spaenefoerderer standard pole guide unabhaenger Laengsschlitten feed to position 1,2,4,5 ...
Schuette multi-spindle rotary machine SF 26-6 1984 built - mechanical gearbox - independent feed from the Laengsschlitten Position 4 - Thread cutting gear with thread cutting spindle
Thread cutting gear Pick-up device partially revised
Schuette multi-spindle rotary machine SF 50/51-6 Rod turning machine run on schneidoel standart Schuetz control mechanical gearbox Hydraulics integrated into the machine with snail-spaenefoerer
Schuette multi-spindle rotary machine SF 26-6 1980 built -with thread cutting device - prepared for centrage suction system - standard Schuetz control D8gdo29 - mechanical gearbox - Balluff cam switch - standard rod guide
Schuette Multi-spindle rotary machine Name: Schuette SF 20-6 Curve controlled Number of spindles: 6 Built: 1980 max. rod diameter: around 20 mm SW 17 mm AK 18 mm VK 14 mm max. rod feed: 80 /(160) mm Number of independent Laengsschlitten: 6 Total / working distances (stand): 63/40 mm " " (special) up to: 100/63mm Number of independent cross slides: 6 Total/ work routes Medium and top slide up to: 32/20 mm Slide up to: 40/25 mm Spindle circle diameter: 224 mm Main times min/max.: 0.36/150 sec. Gv29e0 Off times min./max.: 0.45/0.80 sec. Spindle speed from / to: 900-5000 rpm in the 2nd area: 355-2000 rpm Rated power of the drive motor: 15 KW Connected power: 50 kVA Drive engine speed: 1500 rpm Length Width (in standard performance) 3705 1320 mm incl. rod guide (in standard output) 6335 mm Weight without ro ...
8-spindle rotary machine Built in 1989; serie 25 Refurbished in 2012 • New electrics • New bearings • Guided tours • CNC cross slide in position 7 • Spindle stop setup • Material rod guide • Chip conveyor • Pick-up spindle position 8 • Calibration device • Various tool holders • Various curves
Schuette multi spindle automatic lathe Pour SF 20-6 Curve controlled number of spindles: 6 with mechanical transmission Rod diameter: approx. 20 mm SW 17 mm AK 18 mm UK 14 mm Max bar feeder: 80 /(160) mm Independent longitudinal slide number: 6 Total / working ways (Standart): 63/40 mm (Special) to: 100/63 mm Number of independent cross slide: 6 Total / working ways middle and upper carriage up: 32/20 mm Lower carriage up: 40/25 mm Spindle diameter: 224 mm Main time min/max: 0.36/150 sec. Productive time min./max.: 0.45/0.80 sec. Spindle speed from / to: 900-5000 U/min 2. area: 355-2000 U/min Nominal power of the motor: 15 KW Power supply: 50 kVA The drive motor speed: 1500 rpm Length width (standard execution) 3705 1320 mm incl. Rod Guide (standard execution) 6335 mm Approximate weight without rod guide and accessories: 4.6 to. the rod guid ...
Cam controlled multi spindle automatic lathe, used 6 main spindles, control: Siemens S5 PLC, electronical trip dog control type „Balluff gear box for thread milling (2 pieces) pick up for rear machining in pos. 6, work piece sorting shute, barloader: IEMCA-PRA 40/33 P -rack type- coolant pump, threading clutches, stock stand and reel, tooling: could be different like pictures partly revised
8 main spindles, Chucker AFH130 for complete machining means front- and back side, Control Siemens Sinumerik 840DI, complete revising and new configuration of this machine in year 2010, loading arm, for loading and disloading, Workpiece turn around station in pos. 4 , position 4 with workpiece length control, CNC compound slide in pos. 5, coolant pump with magnet candle filter, tooling: could be different like pictures option: Ergomat TB42 fot cutting off for half finnishing with FMB-Turbo
multi spindle automatic lathe Schuette SF 13 built in 1991 - pick up with back side tooling -Thread cutting gear - chip conveyors - PLC control and much more.
Multi spindle automatic lathe Saeid 13-6 DNT SF Year of construction 1989 Adjustment of speed and cycle time by servo motor Facilities: -Pick-up device with rückw. Editing -Thread cutting gear -Waheed clear text display -pivoting control panels -PLC control etc.
Accessories fur WU 3 ms, apparatus of part of, round loop facility, etc. More info on request
diameter: 160 mm total power requirement: 0 kW Shipping weight: ca. 700 kg Packing: - mm Various chucks, jaws, tensioners etc - see photos The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Axes: 5, sanding length: 330mm, max. workpiece diameter: 235mm, travel X/Y/Z: 400mm/250mm/250mm. Machine dimensions X/Y/Z: approx. 2200mm/1950mm/1900mm, weight: approx. 2800kg, control: Siemens Sinumerik 840D, operating hours: approx. 22000h. Documentation available. An on-site inspection is possible.
number of spindles:8 spindle passage:67 mm Cam controlled multi spindle automatic lathe, used 8 main spindles pick up in pos. 8 threading attachment CNC compound slide in pos. 5, also 2. speed in pos. 2 Hydraulic spindle brake in pos. 4 Incl. length measurement, incl. Brankamp cutting force monitoring tooling: could be different like pictures Please, contact us for getting more informations and pictures on mail@tar-mc.com or www.tar-mc.com
Article: pickoff with shaft Manufacturer: Schütte pickoff with shaft for Schutte multi spindle automatic lathe SF67 pickoff C26GF pickoff shaft C26GF9S1 gear WG-67S holder B73GF1S1 Please, contact us for getting more information and pictures on mail(at)tar-mc.com or www.tar-mc.com
number of spindles:6 spindle passage:18 mm turning length:63/50 mm weight of the machine ca.:8,6 t spindle drive motor:11 kW
number of spindles:6 spindle passage:18 mm turning length:63/50 mm weight of the machine ca.:4,5 t spindle drive motor:11 kW
number of spindles:6 spindle passage:18 mm turning length:63/50 mm weight of the machine ca.:8,6 t spindle drive motor:11 kW
number of spindles:6 spindle passage:18 mm turning length:63/50 mm weight of the machine ca.:4,5 t spindle drive motor:11 kW
