mechanical briquette press briquetting press chip press defective SPÄNEX Type: KS7 Total motor power 13.2 KW Pressing capacity up to approx. 300 kg/h Briquette diameter approx. 50 mm The machine has been in my warehouse for several years. In the briquette press, the brass bearing of the crankshaft is worn. The bearing bushes would have to be replaced. The control system would have to be checked. It is sold as it is, because I clean up my stock. Documents on the machine are available. Condition see pictures, or follow the item description. Parts can also be picked up by yourself. All measurements are approximate. All information to the best of our knowledge but without warranty. Subject to prior sale. The items can be picked up by yourself or shipped at the expense of the buyer. Shipping costs are a guideline, depending on the distance and unloading op ...
Paint mist extraction with supply air system Make Spänex Built in 1995 Paint mist extraction wall Spänex TAW 220 Air volume 6,000 m³/h, motor power 1.35 kW Exhaust pipe diameter 400mm Baffle wall area 2000 mm x 2000 mm Extraction wall depth 800 mm Supply air unit with heating coil Spänex WK 61 for paint room ventilation in cassette design Air flow rate 6,000 m³/h, motor power 2.5 kW Heating medium PWW 90/70 Heat output 77 kW Supply air duct parts Filter Discharge Blanket 1900 mm x 1900 mm x 300 mm Connecting bends, sewer bends Control and regulation cabinet For supply air unit and paint mist extraction
Briquetting Press Briquette Press Spänex Type SHB 50 K1 CE Built in 1986 Hydraulic briquette press With shavings container K1 Briquette mould 8-sided Briquette size 70 mm x 120 mm Capacity 50 kg/h Drive motor 5.5 kW Hours 35665 Wood moisture minimum 8% - maximum 20% Weight of the press 650 kg Chip container size 3m³ Chip hopper with agitator and feed screw Dimensions set-up 1500 mm x 1500 mm, height 2250 mm Almost all shredded materials can be briquetted with a residual moisture content between 6% and 18% without binder. e.g.: wood shavings, milling and sawdust, dust, paper, cotton flaky, coconut, wheat straw, hemp, hay, flax, plant stems, malt germs, ... The maximum chip size should not exceed 20 x 1 mm. Due to their density, briquettes have a volume reduction of up to 90% in the material and thus an extremely high energy and thus calorific value 2.5 kg of ...
Key data: 250 mm, 5 kW, 4700 m³/h
Spänex dust extractor SMU 4500.11 Suction nozzle 250 mm Cleaning vibrating motor Nominal flow rate 4700 m³/h Minimum flow rate 3530 m³/h Motor 5.5 kW Filter renewed
Capacity 250 kg/h Throughput 2.3 m3 Briquette mould 8 square Antireb 11 kw Weight 1200 mg
Warm air heating Spanex UL/E-50 RW-02 with chips 40 kW L x W x H: 1970 x 820 x 1570 cm Weight 530 kg Year 2012 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Volume flow: 4080m³/h, filter area: 34m², BIA category: G, differential pressure: 1650Pa, filtration surface load: 120m³/h-m², air density: 1.2kg/m³, operating temperature: 20°C. Documentation available. On-site inspection is possible.
