Key data: 250 mm, 16 , 1 1/min
available Duplex Extruder! Description attached!
cold feed vacuum extruder Troester 90 mm x 18 D, with feed roller, drive 46 kW, pie speed 10 to 60 rpm, 5 TCU,
cold feed extruder - 60 mm x 18 D vacuum, with feed roller, drive 22 KW, screw speed 10 to 60 rpm, with gear pump, 5 TCU,
90s cold feed extruder, GE 90 x 16 D Vac, make Troester, with large hose / profile spray head, drive 52 KW Siemens AC, 4 TCU Siengle
Key data: 550 mm, 1500 mm
Troester 60 Mill YOM 1990 - refurbished 2014 Drilled Rolls, Hydr. Nip adjustment Stick blender Description attached!
90s cold-feed profile extruder, GE 90 x 16 D Vac, make Troester,
Key data: 90 mm, 16
available Triplex Extruder- Cold Feed with head and feeder. Description attached!
used
Key data: 120 mm, 18 , 45 1/min
Screw with vacuum zone, output approx. 255 - 400 kg/h, straight head
Key data: 120 mm, 22
Output: approx. 255 - 450 kg/h (manufacturer's information from brochures; depending on material and profile; DEGUMA assumes no liability for actual, product-specific output) Straight head on hinged flange, fastening via screws; NEW SEVA motor, new control system
Key data: 1800 mm, 700 mm, 700 mm
available Textile Calendar Complete Line - 2 x let-off, Splicing press, Accumulator, Tension unit, Heting Drums, Calender with thickness measuring, Cooling Drums, Thickness meas. (final product), Accumulator, 2 x Wind-up More details in the attachment!
Key data: 550 mm, 1500 mm
Mixing mill Troester 550 x 1500 mm Bush bearings Motor: 90 kW Friction : 1:1,20 Manual NIP adjustment Stock blender
Profile extruder, GE 90 x 16 D vacuum, make Troester, cold lined
available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!
Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.
Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.
Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.
Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.
screw ø:: für Extruder 90 mm screw length:: -- screw speedl:: -- U/min drive power:: 13,6 kW Condition: little used, as good as new Specification: gear pump ZP 75/50 for extruder size 90 - SEW helical gear units: R 97 - Siemens direct current motor: 1 GG5 118 - Drive power: 13.6 kW, 57 A - curved tooth coupling - With clamp for the head connection, - Clamping flange for extruder and head connection, - Base plate with linear guide rails, - Tooth shaft diameter: 75 mm - tooth width: 50 mm - helical gearing, hardened steel bearings, right-hand drive - without control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll surface width: 450 mm roll diam. toproll: 203 mm roll diam. bottom roll: 203 mm output: 8,8 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
