We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Manufacturer:
(Category: 102-118)
used
turning diameter over bed: 230 mmturning diameter over slide rest: 100 mmturning length: 500 mmturning diameter in the gap: mmturning speeds: 160 - 5000 U/mincentre height: 115 mmspindle bore: mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: 1,5 x 0,8 x 1,6 mMechanics lathe- Collet chuck- Multifix steel holder- Accessories see picturesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Offer 25432 Specifications: - Turning diameter 320 mm - Center width 750 mm - Largest turn – Ø over bed 550 mm - via flat slide 175 mm - Spindle bore 32 mm - Spindle holder - Pick-up cone of the tailstock quill MK 3 - Quill stroke 180 mm - 18 spindle speeds 85 - 2000 rpm - Feeds longitudinal + flat - Metric thread pitches -Thread - Module thread - Diametrical Pitsch thread -Arbor - Cheek chuck -Lunette - Drive 400 V / 2.2 kW - Space requirement approx. W 2100 x D 750 x H 1300 mm - Weight approx. 750 kg
used
turning diameter over bed: 433 mmcentre height: 215 mmcentre distance: 1500 mmturning dia. over face-slide: 267 mmspindle bore: 76 mminner taper MT: 5 spindle turning speed - stepless: 20-1600 U/minweight of the machine ca.: 2.2 tdimensions of the machine ca.: 300 x 120 x 140 cmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
turning diameter over bed: 360 mmcentre height: 170 mmcentre distance: 650 mmturning dia. over face-slide: 196 mmspindle bore: 42 mminner taper MT: 5 spindle turning speed - stepless: 20-3250 U/minweight of the machine ca.: 1,6 tdimensions of the machine ca.: 200 x 125 x 165 cmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Make: Colchester Type / Model: Student Center width: 500 mm Passage: 42 mm Tip height: 175 mm Turning diameter over bed: 350 mm over slides: 200 mm Speed range: 34 to 1,500 mm Feed lengthwise: flat: 0.04 to 0.25 mm/rev Connection: 1.1 / 2.2 kW Accessories: Steel holder, 3-jaw chuck, 4 jaw chucks, steel bracket Weight: approx. 800 kg Dimensions: 1,550 x 900 x 1,200 mm
used
turning diameter over bed: 330 mmturning diameter over slide rest: 210 mmturning length: 635 mmcentre height: 165 mmspindle bore: 42 mmturning speeds: 22-1800 U/mintotal power requirement: 2,2 kWweight of the machine ca.: 1.000 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
turning diameter over bed: 400 mmturning diameter over slide rest: 246 mmturning length: 635 mmcentre height: 195 mmSpindle Speed: 15-2500 UpMspindle bore: 54 mmtotal power requirement: 7,5 kWweight of the machine ca.: 2.500 kgdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Tip height: 195 mm Center width: 1250 mm large recirculating Ø over bed/support slide: 400/265 mm Spindle Holder/Bore: Camlock D1-6"/54 mm Tailstock quill taper: MK 5 Spindle speeds infinitely variable in 3 groups: 0 - 2500 rpm Feeds longitudinal: 0.018 - 1.2 mm Feed plan: 1/2 of the longitudinal feeds 51 metric thread pitches: 0.2 - 14 mm 56 Inch Thread: 2 - 56 Gg/" 20 module threads: 0.2 - 3.5 module 20 Diametrical Pitch Threads: 8 - 56 DP electr. Connection: 400 V, 7.5 kW Weight: 1500 kg Space requirement: 2500 x 1300 x 1300 mm
used
turning diameter over bed: 400 mmcentre height: 195 mmturning diameter over slide rest: 246 mmturning length: 1250 mmspindle turning speed - stepless: 0-2500 U/minweight of the machine ca.: 1,8 tdimensions of the machine ca.: 2x1.3x1.6 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
turning diameter over bed: 400 mmcentre height: 195 mmturning diameter over slide rest: 246 mmturning length: 1250 mmspindle turning speed - stepless: 0-2500 U/minweight of the machine ca.: 1,8 tdimensions of the machine ca.: 2x1.3x1.6 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
turning diameter over bed: 400 mmcentre height: 195 mmturning diameter over slide rest: 246 mmturning length: 650 mmspindle turning speed - stepless: 0-2500 U/mintotal power requirement: 7,5 kWweight of the machine ca.: 1,8 tdimensions of the machine ca.: 2x1.3x1.6 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Conventional lathe COMEV 200, 200 x1000 mm., Information about technical data are not binding., Machine available subject to prior sale., Height centres: 200 mm, Swing over crosslide: 230 mm, Distance between centres: 1000 mm, Bed width: 280 mm, Spindle nose cam-lock din55029: 6 , Spindle bore: 52 mm, Spindle speed: 25 - 1600 rpm, Number of spindle speeds: 16, Spindle motor power: 3 Kw, Tailstock quill diameter: 52 mm, Taper of quill mt: 4, Approx net weight: 1.300 Kg
used
Turning diameter over face slide: 200 mm Spindle bore: 32 mm Circumferential diameter over bed slide: 315 mm Tip width: 600 mm Turning length: 560 mm Quill stroke: 140 mm Total weight: 1,750 kg Digital display Heidenhain Collet System E163
used
: Aufnahmen Divers K50 Diameter: 50 mm: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Leit & Pull Spindle Lathe "DREHMA - D410x1500mm -Demonstration machine - year 2025 -CE - Identifier -Digital display -Turning diameter over bed 410mm -Turning length 1500mm -Turning diameter over support 255mm -Turning diameter in the offset 580mm -Spindle Passage 52mm -Speed range 45-1800 rpm -Automatic longitudinal/plane feeds -Thread/Inch/Metric etc. -Tailstock Mk4 -Central lubrication -Drive power 3.5 KW -Fixed / Rotating bezel -Multifix holder with 4x inserts -Three-jaw chuck 200mm Hsbknowatv Ss Au S Tel -Four-jaw chuck 250mm -Face Plate -Lining protection -Front safety device -Coolant device -Work light -Running tip -Machine feet Dimensions: LxWxH 2.5x1x1.6 meters / Weight 1800Kg
used
turning diameter over bed: ? mmturning diameter over slide rest: ? mmturning length: ? mmtotal power requirement: ? kWweight of the machine ca.: 1,5 tdimensions of the machine ca.: 2,511,5 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
This offer is aimed exclusively at entrepreneurs within the meaning of § 14 BGB. The price is net plus 19% VAT. Manufacturer: EST Ticino Type: ET-BM 400 Turning length: 1500 mm Turning diameter bed Ø: 800 mm Turning diameter slide: 470 mm Turning diameter pit Ø: 400 mm Pit length: 750 mm Spindle bore: 130 mm Power spindle: 15 kW Bed width: 600 mm Quill: 130 Ø Stroke quill: 300 mm Spindle mount: 6 Mk Speed: 600 rpm Dimensions (estimated) Length: 4500 mm Width: 1800 mm Height: 1800 mm Weight: 5200 kg with accessories: -Safety equipment - Face plate, four-jaw chuck, clamping jaws, tool holders, tips, drill chucks, tools All information is made to the best of our knowledge, errors excepted. The sale is subject to exclusion of any warranty. The exclusion does not apply to claims for damages arising from grossly negligent or intentional breach of the S ...
used
Lead & Pull Spindle Lathe EXCELLO - DLZ 500 SL -Tip height 250mm -Turning diameter over bed 500mm -Turning diameter over support 310mm -Center width 3000mm -Rod passage 65mm -Speeds: 28-1400 rpm -Automatic longitudinal/plane feeds -Three-jaw chuck 250mm -Four-jaw chuck 250mm -Multifix base holder with inserts -Bezel -Tool cabinet -Documentation Dimensions: LxWxH 5.5x1.4x1.6 meters / Weight 3500Kg
used
GALLIC 16 N lead and pull spindle lathe with ACU-Rite digital display - Turning diameter over support 200mm - Turning diameter over bed 320mm - Tip height 160mm - Center width 1000mm - Speed range 45-2500 rpm - Spindle bore 40mm - Automatic feeds X/Z axis -Spindle bore approx. 42mm -Quick-change holder -Thread/Metric/Inch etc. -Tailstock MK 4 -Electric lining protection -Three-jaw chuck -Swarf back wall LxWxH 2.4x1x1.7 meters / Weight 1600Kg
used
Guide & Tension Spindle Lathe GEMA LZ 200 -Three - Axis Digital Display "NEW" -Guided tours " VERY GOOD" -Tip height 200 mm -Center width 1000 mm -Turning diameter over bed 400mm -Turning diameter over support 200mm -Spindle passage 54 mm -Automatic longitudinal/plane feeds -Speed range 36-2200 rpm -Tailstock MK 4- Adjustment 200mm -Three-jaw chuck 250mm -Electric lining protection -Multifix with inserts -Coolant device -Work light -Machine feet -Chip tray Dimensions: LxWxH 2x1.2x1.6 meters / Weight 1800Kg
used
: gefült mit 43 Aufnahmen height: 2.200 mmwidth: 1.200 mmweight of the machine ca.: 300 kg: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
: . centre distance: 3000 mmmax. swing diameter: 660 mmmultifix: . steady: 2 Stück weight of the machine ca.: 5 t: KW 39/2022 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
serial number: 80131-0271 centre distance: 2000 mmcentre height: 250 mmbore diameter: 63 mmwith digital read-out: K+C Easson10L voltage: 380 V: 220 Vampere: 16 AThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Hello, I get this lathe at the beginning of August. With a lot of accessories: steady rest, lathe chuck – clamping jaws, quick-change holder and.. Heidenreich & Harbeck Type Hanseat 480 Year of manufacture 1980 Center height 255 mm Turning diameter over support 300 mm Center width 1500 mm 24 speeds from 23.6 to 2500 n1/min Tailstock MK 4 Chuck F 250 Motor 380 Volt 11 kW Transport dimensions: Length 3200 mm Width 1200 mm Height 1550 mm Weight 2.5 to. Lathe Hanseat 480 incl. accessories St Description 1 instruction manual 1 Lynette small 1 Lynette large 1 4- Jaw chuck small 1 4- Jaw chuck large 15 quick-change tool holders Set designation 2 jaws for 4-jaw chuck 38 jaws for 3-jaw chuck
used
Tip height: 355 mm Center width: 3000 mm large circulation Ø over bed/recess/bed slide: 715/790/520 mm Spindle bore: 86 mm Spindle holder according to DIN 55027: Gr. 11 Tailstock quill taper: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/flat: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitwort Thread: 2 - 28 Gg 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 Diametrical Pitch Threads: 8 - 112 DP Drive motor, pole-switchable: 380 V, 7/11 kW Weight approx.: 7 t Approx. space requirement: 6000 x 2300 mm
used
Offer 26143 Technical data: - Tip height 165 mm - Center width 750 mm - Turning diameter over bed 330 mm - Turning diameter via face slide 170 mm - Spindle bore 42 mm - Pick-up cone of the tailstock quill MK 3 - Travel of the tailstock quill 140 mm - Spindle speeds 18 - 2000 rpm - Feeds longitudinal + flat - Metric thread pitches - Inch thread - Module thread - Drive 400 V / 1.5 / 2.8 kW - with: - 2 pieces 3 jaw chucks - Bezel - 4 pieces SWS steel holder - Div. Drehmeisel - Space requirement approx. W 1800 x H 1150 x D 900 mm - Weight approx. 800 kg
used
turning diameter over bed: mmturning diameter over slide rest: mmturning length: mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: 0390 mm: 240 mm: 1000 mm: 190 mm: 54 mm: 5,5 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: 0390 mm: 240 mm: 1250 mm: 190 mm: 54 mm: 5,5 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
: 0390 mm: 240 mm: 1250 mm: 190 mm: 57 mm: 5,5 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
KNUTH Basic Plus L&Z Lathe /Year 2011 -Tip height 150mm -Max turning diameter 300mm -Max turning diameter over support 178mm -Max. turning diameter without bridge 430mm -Tip width: 810 mm -Spindle bore: Ø 38 mm -Spindle speed: 60–1,550 rpm, 9 steps -Automatic longitudinal/plane feeds -Spindle mount: Camlock D1-4" -Tailstock cone: MK 3 -Quill stroke: 100 mm -Bed width: 180 mm -3-axis digital display -Multifix quick-change holder with insert -Electric lining protection -Work light -Rotating center punch tip -3-jaw chuck -2x bezels -Documentation Dimensions: LxWxH 1.6x0.7x1.2 meters / Weight 520Kg
used
Well-preserved precision lathe with extensive equipment
used
Specifications: Tip height: 140 mm Turning length: 500 mm Accessories (included): Lunette Multifix "A" Collets 0.5 – 24 mm Milling device (Y-axis) 3-jaw chuck 125 mm Cs Urh Axexlr Hkszorh Face Plate 260 mm Running tip Chuck Die stock 4-jaw chuck Coolant pump Instruction manual (German)
used
turning diameter over bed: 260 mmturning diameter over slide rest: 150 mmturning length: 400 mmturning diameter in the gap: mmturning speeds: 235 - 2800 U/mincentre height: 130 mmspindle bore: 26 mmtotal power requirement: kWweight of the machine ca.: 0,5 tdimensions of the machine ca.: 1,25 x 0,8 x 1,2 mMechanics lathe- 3-jaw chuck 160 mm- Accessories see picturesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Description Lead and Pull Spindle Lathe Lieber LSD S Details Machine no. 1770 Year of manufacture 1984 Height 1,800 mm Width 1,700 mm Length 2,600 mm Bed width 500 mm Bed height 850 mm Bed length 1,600 mm Face Plate Ø 900 mm Forkardt chuck Ø 400 and 500 mm possible (by arrangement) Tailstock MK4 mount max. workpiece lengths 1,000 mm Turning diameter over bed 920 mm Center height 460 mm Turning steel holder will be added
used
turning diameter: 125 mmturning length: 560 mmswing diameter over bed slide: 250 mmturning speeds: 30-3000 U/mintotal power requirement: 10 kWweight of the machine ca.: 1.5 tdimensions of the machine ca.: 2 x 2 x1.5 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Center height: 300 mm Center width: 1000 mm Circumferential Ø: over bed 610 mm Spindle bore: 71 mm Spindle mount: size 8 Pick-up cone tailstock: 5 MK Spindle speeds: approx. 11.2 - 1800 rpm Feeds: longitudinal/flat 0.014-16/0.063-7 mm/rev Thread pitches: 0.1 - 112 mm Electrical connection: 380 V, approx. 5.5 kW Space requirement: 2900 x 1450 x 1750 mm
used
Tip height: 205 mm Center width: 1500 mm Circumferential Ø: over bed 410 mm Spindle bore: 47 mm Spindle holder: size 6 Pick-up cone tailstock: 4 MK Spindle speeds: 28 - 1250 rpm Feeds: longitudinal/flat 0.03-1.3/0.008-0.33 mm/rev Thread pitches: 0.25 - 76 mm Electrical connection: 380 V, 3 kW Space requirement: 2800 x 1100 x 1600 mm Weight: 1330 kg
used
Year of manufacture 1980s/90s Technical data: Tip height: 185 mm Center width: 750 mm Turning diameter over bed: 370 mm Spindle bore: 36 mm Bed width: 250 mm Speed range: 38 - 1600 rpm Tailstock mount: MK 3 Quill stroke: 110 mm Dimensions (WxDxH), approx.: 1950 x 900 x 1200 mm Weight, approx.: 800 kg Equipment: - 3-jaw lathe chuck, brand: Röhm, ø 200 mm - Quick-change holder with 4 inserts - Bed stop - Chip tray
used
Tip height: 175 mm Center width: 800 mm Circumferential diameter over bed: 350 mm Circumferential diameter over support: 310 mm Spindle bore: 46 mm Speed range: 25 - 2000 rpm With digital display
used
Circulation over bed 560 mm Wire diameter over carriage 365 mm Turning length 2000 mm Spindle head DIN 55027 Front bearing 100 mm Spindle bore 62 mm Spindle speed 11.2 - 2240 rpm Spindle motor 15 KW Face slide travel 345 mm Upper slide travel 125 mm Bed widthw 360 mm Quill cone i. tailstock 5 MK Quill diameter 80 mm Quill stroke 190 mm Thread pitches 0.125 - 112 mm Machine weight 4500 KG Dimensions 3.5 x 2.0 x 2.2 m 3-axis digital display 3-jaw chuck 1 roller bezel MULTIFIX steel holder Sleigh rush walk Equipment for Metric, Inch, Module & Diametrical Pitch Threads Geometric overhaul in 2023, little used, excellent condition!
used
Optimum Lathe D330 x 1000 SG -Center width: 1000 mm -Circumferential diameter over bed: 330 mm -Circumferential diameter over support: approx. 190–200 mm -Spindle bore: approx. 38 mm -Spindle mount: Camlock (mostly D1-4) -Speed range: approx. 70 – 2000 rpm (stepped) -Feeds: longitudinal and flat, automatic -Threading: metric and imperial possible -Motor power: approx. 1.5 – 2.2 kW -Voltage: 400 V / 3 phases -Tailstock mount: MK3 - Spindle holder: MK5 -Work light -Three-jaw chuck -13x Face Plates/Drive Plates -Multifix with 1 steel holder -Machine feet -Lining protection Dimensions: LxWxH 1.9x0.7x1.5 meters / Weight 700Kg
used
Optimum D460x1500 lathe – fully functional Description: For sale is a used Optimum lathe D460x1500, built in 2006/01. The machine is fully functional and ready for immediate use in the workshop and production. It is ideal for turning medium-sized metal and steel parts. Technical data: Manufacturer: Optimum Model No.: D460x1500 Year of construction: 2006/01 Circumferential diameter over bed: 460–465 mm Circumferential diameter over upper slide: 270 mm Circumferential diameter without bed bridge: 690 mm Center width: 1500 mm Tip height: 230 mm Bed width: 300 mm Spindle bore: 58 mm Spindle cone: MK 6 Spindle mount: Camlock ASA D1–6 Speed range: 25 – 2,000 rpm⁻¹ Longitudinal feed: 0.031 – 1.7 mm/rev Transverse feed: 0.014 – 0.784 mm/rev Thread metric: 0.1 – 14 mm Thread imperial: 1/2 – 2 gears/inch Motor power ...
used
turning diameter over bed: / mmturning diameter over slide rest: / mmturning length: / mmtotal power requirement: / kWweight of the machine ca.: / trequired space: / mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Center distance 6000 mm Height of centers 400 mm Max diameter on the bench 800 mm Max diameter on the carriage 520 mm Max diameter in the recess 1100 mm Bar passage 130 mm Undercarriage stroke notes 340 mm TURRET Standard BENCH Max weight between tips 3500 Kg Max weight on steady rests 4500 Kg Pallet width 520 mm TAILSTOCK Steerer diameter 115 mm Steerer stroke 380 mm Cone cm6 HEAD Spindle power 25 Kw Spindle speed 5/1000 Rpm 11 cam-lock spindle attachment Spindle torque 560 Nm GiVi axis display measurements Self-centering 500 Use and maintenance books Yes Wiring Diagrams Yes Protections yes Ready for availability Visible in the warehouse in operation
used
Digital Turning diameter 120 mm Turning length 700 mm Spindle speed 2000 min-1 Tailstock
used
turning length: 3500 mmturning diameter: 1000 mmturning diameter over bed: / mmweight of the machine ca.: ca. 8,5 tincluding 2 lynettes and large face plateThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
: . : 1990 centre distance: 1400 mm: 505 mm digital readout: . bed bridge: . tool adaptor: multiple Aufnahme weight of the machine ca.: 2,3 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Swing over the bed: 1250mm Max length of the workpiece: 10000mm Max mass of the workpiece at machining between centres with rest: 10000kg Height of the cutting tool set in tool holder: 50mm
used
Offer 24204 Technical data: - Largest turning diameter over bed 420 mm - Center width 1000 mm - Spindle bore mm - Mounting cone of the tailstock quill MK 4 - Travel of the tailstock quill 200 mm - Spindle speeds 40 - 2000 rpm - Feeds longitudinal + flat - Metric thread pitches - Inch thread - Module thread - Drive 400 V - with: - 3 jaw chucks - SWS steel holder with 3 inserts - Space requirement approx. W 2800 x H 1250 x D 950 mm - Weight approx. 2200 kg