used Rolling mills for sale

Manufacturer: Berstorff Type: 1200 x Ø 450 mm Year of manufacture: 1961 / revised by DEGUMA Engine No.: 60-20409 Rolls: 1200 mm roller length 450 mm roller diameter Cylindrical rollers, smooth roller surface Roller cooling: Central bottle neck bore, with NEW ROTOFLUX rotary unions Speed: Fixed speed, non-variable Rear roller: 18.2 rpm = 25.7 m/min Front roller: 16 rpm = 22.6 m/min Friction: 1 : 1.14 – new coupled wheels Roller bearings: plain bearings, very good condition, bearing journals reground during last revision Lubrication: Automatic oil circulation lubrication with electric pump Gap adjustment: Manual by ratchet; Display via scale on the stand Roller breakage protection: fracture plates Guide jaws: 2-part, moving material wiper jaws made of steel with center sword; Firmly attached to the bearing housings, cannot be swivelled Material pan: Sliding sheet steel ...

Rolls diameter: 500mm. Working length 1500mm. Motor power 90kW Siemens controlled by frequency inverter Omron A1000. Main drive realized by herringbone gear wheels. Machine has most effective pneumatic disc safety brake. Motorized roll gap adjustment (Siemens motors)). Machine is after full modernization in 2017 and adapted to the minimum safety requirements. Programmable safety relay SICK Flexisoft. Limit switches Schneider, string safety switches Allen Bradley, emergency stop switches Eaton and Schneider. Operating panel Proface GP-4201TW. Autonomous lubrication station for rolls bearings lubrication. Self-supporting base plate with rubber vibrations absorbers . Technical documentation is available.

4 nos. Buzuluk 84 Mills available! Drilled Rolls, Rollerbearings, electrical Nip adj., Bullgear Drive 2 x left Hand Drive 2 x Right Hand Drive Description attached!

Year of manufacture: 1989 / currently revised by DEGUMA Machine No.: 1150-22-89 Rolls: 400 mm roll width / 350 mm usable roll width 150 mm diameter - Cylindrical rollers - Chrome-plated surface - Root ball condition very good - Height of the top of the roller to the floor: 1200 mm Roller temperature control: Peripherally drilled rollers - Oil-tempered via rotary unions in both rollers; - Temperature control unit is NOT included in the scope of delivery - this can also be offered as a used device on request Roller speed: Speed of the front roller variably adjustable - Infinitely adjustable via input on the control panel) - Rear roller speed depends on the set friction Front roller: 1 – 21.4 rpm = 1 – 10.7 m/min Rear roller: 1 – 21.4 rpm = 1 – 10.7 m/min Friction: Adjustable in the range of 2:1 – 1:2 by independently adjustable speed of both roll ...

Year of manufacture: approx. 1980 / 2024 completely overhauled by DEGUMA Machine No.: Unknown Rolls: 1000 mm roller length 400 mm roller diameter Cylindrical rollers, smooth roller surface (no fluting) - Roller bales and bearing journals reground Roller temperature control: Water cooling via central bottle neck hole, with NEW ROTOFLUX rotary unions with spray lances (Connections: 1 inlet; 11/2 drain) Speed: Infinitely variable via potentiometer Tight roller: 1 - 20 rpm = 2 - 25 m/min Adjustment roller: 1 - 16.4 rpm = 2 - 20.5 m/min Friction: 1 : 1.22 - NEW coupling wheels - Fixed friction ratio; not adjustable Roller Bearings: 4 NEW Bronze Plain Bearings - NEW silicone gaskets Lubrication: Recirculating oil lubrication with electric pump - NEW Electrical Flow Monitoring Gap adjustment: Electromotive - 2 NEW three-phase motors 1.5 kW - NEW magnet ...

Refer to code 1071-1072-1073-1074-1075-1076 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased as is without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1154 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased as is without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1152 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased as is without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1089-1090 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased as is without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1153 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased as is without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1063-1064-1067 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased as is without warranty, or completely rebuilt and guaranteed as new machine.

17” (430mm) wide x 9” (230mm) diam. Francis Shaw Two Roll Mill Right angle drive No rotary joints One-piece fabricated bedplate Brooke motor 20HP Scraper blade front Bull wheel drive Holroyd Gearbox Caliper brake Control Panel Dims: 2.2m wide x 1.7m deep x 1.7m high

Iddon 24inch (600mm) x 12inch (300mm) Two Roll Mill Chilled cast iron rolls Rotary joints Right angle drive Radicon Gearbox Fulton Rotary joints AEI electric construction motor Safety bar back and front of mill

Refer to code 1155 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased as is without warranty, or completely rebuilt and guaranteed as new machine.

Two Roll Rubber Mixing Laboratory Mill Manuf.: JRD Bipel 300mm x 150mm rolls Roller type bearings Nip fully guarded Motorised nip adjustment Roller speed variable up to 32 rpm Friction ratio 12:1 Grease lubrication Roller reverse system

Open Mill Roll diameter 550mm Roll length 1530 90 KW

Year of manufacture: 1963 / Control system renewed in 1985 Rollers: 225 mm bale width 110 mm diameter Cylindrical, smooth roller bales Temperature control: Chamber-drilled rollers, oil-tempered via rotary union and spray lances Speed: Infinitely adjustable Solid roller: 11 - 63 rpm = 3.8 - 21.8 m/min Adjustment roller: 11 - 63 rpm = 3.8 - 21.8 m/min Friction: Infinitely adjustable Bearing: Bronze Plain Bearing Lubrication: Electric oil circulation lubrication Gap adjustment: Manual with ratchets Material guide jaws: Two-piece with centre centreboard, non-folding Material tray: plastic tray below the rollers, can be pulled out by hand Motor: Two SEW three-phase brake motors with 2.2 kW each, 230/400 V, 50 Hz, 1395 rpm Transmission: Two PIV gearboxes (for speed control) in combination with two JAHNEL helical gearboxes Control: Conventional ...

Year of Make: 1990 Make No.: 6439 Rollers: 350 mm roller width 110 mm diameter - Cylindrical, smooth surface - Height of the top of the roller to the floor: 1200 mm Roller temperature control: Electrically heated up to 300°C via electric heating rods; - Water-cooled via new spray lances and NEW rotary unions in both rollers; - Without temperature control unit Speed: Infinitely adjustable via frequency converter Adjustable roller: max. 22.5 rpm = 7.8 m/min Fixed roller: max. 27 rpm = 9.3 m/min Friction: Switchable friction ratio (friction or synchronization) - 1 : 1.2 or 1 : 1 Roller bearings: Bronze plain bearings Bearing Lubrication: Oil Circulation Lubrication Gap adjustment: Manual manual adjustment by crank - Parallel adjustment of both sides Gap Indicator: Mechanical Analog Dial Gauge Material wiper jaws: One-piece metal scrapers - Manu ...

Power supply Voltage V 380 Type of current three-phase current Frequency Hz 50 Amperage A 30 Connected load kW 18 Electrical fuse A 63 Cooling water requirement 1/min 10 Characteristics Roller diameter mm 150 Roller width mm 450 Working width mm 350 Batch volume dm³ 1 Drive Rear roller speed 1/min 20 Speed front roller 1/min 10 - 20 Friction 1 : 2 Drive torque Nm 2000 Drive power kW 8.0 Heating Surface temperature °C up to 220 Heating type: electric Heating capacity per roller kW 5.5 Total heating capacity kW 11.0 Temperature Control Electronic Controllers with recirculation Switching behavior PID Temperature Sensor Resistance Thermometer PT 100 Dimensions Machine length mm 1600 Overall length (incl. water connection) mm approx. 2000 Machine width mm 750 Machine height mm 1600 Working height mm 1200 Work surface requirements m x m ...

Year of manufacture: 1991 / 2023 revised by DEGUMA Make No.: 6552 Rollers: 750 mm roller width, 650 mm working width 300 mm diameter Cylindrical, smooth surface Working height: 1350 mm Note: on the roller bales there are several traces of indentation of screws Roll gap: 0.5 – 25 mm Rear roller speed: 2 – 26.5 min-1 Friction: switch for synchronization and fixed friction 1 : 1.82 Gap adjustment: electric gap adjustment Gap display: digital Material wiper jaws: 2-piece steel wiper jaws, foldable Surface temperature Roller: up to 220 °C Heating type: electric Heating capacity per roller: 18 kW Temperature control: electronic regulator with feedback Temperature sensor: RTD PT 100 Roller cooling: medium water, connection inlet Dmr. 12 mm, connection outlet Dmr. 22 mm, water pressure approx. 4 bar New rotary unions, without temperature contr ...

Rollers: 450 mm roller width 200 mm diameter Cylindrical, smooth surface Height of the top of the roller to the floor: 1340 mm Roller temperature control: water-cooled, spray lances in both chamber-drilled rollers, Without temperature control unit Speed: Infinitely adjustable via frequency converter Adjustable roller: max. 28 / 24 rpm = 17.6 / 15.1 m/min Fixed roller: max. 34 rpm = 21.3 m/min Friction: Switchable friction (switchable by lever) 1:1.2 and 1:1.4 Roller bearings: Bronze plain bearings Bearing Lubrication: Oil Circulation Lubrication Gap adjustment: Manual manual adjustment by ratchet; Separate setting for right and left side Gap Indicator: Mechanical Analog Dial Gauges Material wiper jaws: Two-piece metal wipers; not foldable • Strippers move with the adjustable roller when adjusting the roller gap and are therefore always in ...

Troester 60 Mill YOM 1990 - refurbished 2014 Drilled Rolls, Hydr. Nip adjustment Stick blender Description attached!

Troester / Uth WMX-20 / 72 Mill drilled Rolls Roller bearings Single Drive Hydraulic Nip adjustment Stick blender on Baseframe Description attached!

Refer to code 1171 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased as is without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1170 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased as is without warranty, or completely rebuilt and guaranteed as new machine.

Rolls: dia. 400 x 1000 mm Rolling surface: smooth Roller Type: hollow bored Manuel nip adjustment Engine: 63 kW Conversion to CE in 2010

Rolling mill in very good condition. Used. Without CE.

STOCKBLENDER: 1000 / 1500 / 2540 - COMERIO ERCOLE / OMG / LTC / MECCANICHE MODERNE / LAMPERTI Refer to code 1034-1035-1036-1037-1038-1039-1040-1041 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased as is without warranty, or completely rebuilt and guaranteed as new machine.

Year of Make: 1973 Make No.: 1413; Com: 23243 Rollers: 350 mm roller width 150 mm diameter Cylindrical, smooth surface Height of roller top to floor: 1020 mm Roller temperature control: chamber-drilled rollers Speed: no speed control Friction: 1:1.23 Roller Bearings: Plain Bearings Bearing Lubrication: Grease Cartridges Gap adjustment: Manual manual adjustment by spindles; Gap indicator: on scale on the adjustment spindle Material wiper jaws: Two-piece, fixed with PA6 coating Material tray: below the rollers Main drive: SEW-Eurodrive 7.5 kW, 380 V, 50 Hz Gearbox: SEW spur gear, n1: 1,400 min-1, n2: 85 min-1, i: 16.47, immersion bath lubrication Safety: Emergency retaining bracket above the rollers Control: simple contactor control with brake motor El. Connection: 3 Ph., 400 V, 50 Hz Dimensions: approx. 2,000 x 1,000 x 1,700 ...