Vacuum forming machine for the production of PS, PVC, PET, blister, tray packaging. The thermoformer works separately forming and punching. The machine is in very good condition and was only used as a back-up machine for 16 years. It has been cleaned and extensively tested. so that it is immediately ready for use. Currently, a tool for trays in the size 125x176 mm is installed (forming tool 3-fold, negative, top), tool size approx. 188x408mm. We are also happy to put you in touch with a very good toolmaker who can produce format tools according to your wishes. Equipment of the machine: Moulding area 350 x 500 mm Film width max. 540 mm Moulded part height max. 100 mm positive - Top heating longitudinal row control - Underheating longitudinal row control - Strip steel cut heating - Forming station pneumatic, undertable as cooling plate - Needle chain transport with servo ...
M. No.: 322 Max. film width 700-800 mm Equipment / Additional information: -GREINER STACKING / Transfer device R3 (Ref. No.: 95002.24) // M. No.: 00020 // Age: 1998 Heating from above and below Material PS and PP were processed 450 Ps // 350 Pp The following tools were used on the machine: 8-way WZ-Ø95 and 15-way WZ-Ø73 and 15-way WZ-Ø86 Packaging was produced especially for the dairy industry. The cycles are 18-25 strokes - depending on the cup weight.
Thermoforming machine Illig UA150U, year of construction 1991, S/N 585, max. power 14.6 kW, with control Schleicher PGS, motor-driven conveyor belt, length approx. 1,500 mm, with lot of tools for thermoforming machine Illig, individual listing is not available, in stock on shelves in the basement and at the thermoforming machine
Thermoforming machine Illig RDM-50 K • Year of built 1994 • Suitable for processing PS and PP • Forming area 500 x 280 mm • Max material width 525 mm • 200 mm air cylinder for per-stretcher • Servo driven main engine and material transport Specifications • 7 upper heating zones • 7 lower heating zones • Tool temperature control • Separate down holder cooling • Material sag control Additional equipment • Foil unwinding station • Endless stacking unit Good condition, available immediately
ILLIG UA 200 G thermoforming machine was built in 1990 in Germany. This highly efficient machine is used in the production of high-quality plastic parts, such as tubs, containers and car parts. As the ILLIG thermoforming line is equipped with two material feeders, the thermoforming process is fully automatic and also allows machining in sheets or from a roll. Technical data of the ILLIG UA 200 G thermoforming machine - maximum mould dimensions (L x W): 1960 x 980 mm - minimum mould dimensions (L x W): 860 x 720 mm - total heating capacity: 87.2 kW - maximum operating pressure: 10 bar - material feeder (2 pcs.) - power supply: 3x 380 V; 50 Hz
ILLIG RDM54K, age 2006 Preheater ILLIG VHW 72, 2-Roll ILLIG RDM54K with Indramat Servomotor Indexing Max. Film width 545 mm Double Heating, Heating Capacity 45.10 kW Max. Form area: 520 x 300 mm Indramat Servomotor Plug Assist Max. depth Draw: 125 mm Auto Transport Rail Spreading for PP Auto. Sheet Sag Control Inline Counter/ Stacker ILLIG SZA Inline Grinder ILLIG RS75b (High Version) with blower Siemens SIMATIC MULTI Panel Color Display, with Touchpad Controls Siemens S7 PLC
ILLIG SZS73 Counter Stacker, age 2007 Effective Working Area: 740 x 340 mm Max. Part Height: 150 mm Formed Part Stacking Length: 800 mm Siemens S7 PLC Controls Siemens SINAMICS Motor Drives Rittal Control Cabinet Cooling Unit with Temperature Display. This ILLIG SZS73 was working Inline with a Generation 3 ILLIG RDM70K Line. With Snap -Stacking Brush Stacking Cascade Stacking The Counter/ Stacker is in v. good production Condition, it is clean and in a very good Optical condition as well
Illig SK 74-C from a workshop for the disabled Year of construction 2006 Serial No.426-0172 JM80Q2 +2 pallets with approx. 38 rolls of film Dimensions in mm approx. 2200x1600x1600
Illig SB 53- C from a workshop for the disabled with few operating hours Serinenr. 233-2484 Siemens Simatic control system Dimensions in mm approx. 2000x1600x1000 for transport reasons, the cylinder was removed (see photo) Also for sale: Illig SK 74-C from 2006
ILLIG PLS75B Inline Counter/ Stacker, with Hole Punch Station, age 2006 used Inline with ILLIG RDM75K ! Max. Stacking Area: 750 x 350 mm Min Height of formed product: 25 mm Max. height of Formed Product: 150 mm Min. dia. of product : Ø 40 mm Max. dia. of Product: Ø 150 mm Max. length of Product Stack: 730 mm Output rate of Product Stacks: 1200 Stacks/ hr Rotating Head to neatly remove Products from the Thermoformer Mold Inline Hole Punch Station Inline Counter Stacker Station Compressed Air: 0.2 L at 6 bar, approximately Total Drive Rating: 19 kW Electrical specifications: 400 V, 3 phase, 50Hz (N/ PE) Cross delivery conveyor for counted cups. All Motors are Indramat Servo Motors Siemens SIMATIC TOUCH LED Operator Control Panel with Touch Pad Controls Siemens S7 PLC Controls Delivers Counted Cups/ Containers at Right Angles to machine direction New (Feb- ...
Illig RDM75K age 1998, refurbished in 2019, with Siemens S5 PLC Controls, used only for ca. 50,000 hrs ELAU B1 Display with Touchpad controls Thermoformer with auto-start facility Indramat Servomotor Indexing Max. material width 750 mm Max. Indexing length 480 mm Top & Lower heaters, total connected load top & bottom heaters 111.3 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 700 x 450 mm Hydraulic Cylinder Plug Assist with Bosch Rexroth Hydraulic Power Pack, completely Overhauled in 2019 Max. Part height 150 mm Max. Mold closing force 25,000 daN Auto Lubrication system Siemens S5 PLC Controls New original ILLIG/ RITTAL Control Cabinet Cooling System added in May-2023.
Illig RDM 37/10 Thermoforming Line - Made in Germany - Year of construction: 1986 - Under & Top Heating - DIV - Moulding area: 475 x 250 mm max. - Film width: 495mm min / 150mm max. - Refurbished: new bearings, new bolts, new bushings & electronics, etc. - Fully functional - with many accessories - several different forming tools Produce cups, bowls and similar products with the ILLIG RDM37/10 pneumatic forming machine. The thermoformer with forming/stamping technology works reliably with precision mechanical drives and delivers high molded part quality and performance.
M. No.: 322 // Counter: 80188 hours Max. film width 700-800 mm Equipment / Additional information: The machine is constructed as follows: -Greiner stacking / Transfer device R3 (No.:00020) // Age: 1998 -ILLIG mill RS75B // Age: 1999 Control cabinets, etc. Heating from above and below Material PS and PP were processed 450 Ps // 350 Pp
Technical specifications: Rated power, kW: 11,3 Mold area, mm: 475 x 250 Max. film width, mm: 495 Min. film width, mm: 150 Max. feed length, mm: 280 Min. feed length, mm: 50 Max. drawing depth/negative, mm: 100 Number of cycles/min.-max.: 48 Consumption of air/cycle at 6 bar: 100 Nl (net-pressurized air) Heat energy to be dissipated: with top heating ca. 10 260 KJ/h with top and bottom heating ca.: 17 715 KJ/h Special equipment: Hollow floor facility available Control cabinet: included
THERMO FORMING MACHINE ILLIG RDM K 50 WITH INLINE EXTRUDER (COMPLETE LINE) M. No.: 322 Counter: 80188 hours // Power: 800-1000 kg/h Max. film width 700-800 mm Equipment / Additional information: The machine is constructed as follows: -Kuhne Extruder KF70E & Co. Extruders K45-24D -Colotronic dosing unit CSK30 with 4 components -Kuhne smooth and cooling rolls (calendering) / GA4/900; puller: BA2-1/900 -Thermoforming machine ILLIG RDM K 50 -Greiner stacking / Transfer device R3 (No.:00020) // Age: 1998 -Illig mill RS75B // Age: 1999 Fully existing infrastructure; control cabinets, pumps, etc. Heating from above and below Material PS and PP were processed
ILLIG STAL80 Trim Press, age 1988:- Technical data ILLIG STAL 80 : Punching table area max. 1000 x 510 mm Material width max. 800 mm Infeed length 20 - 400 mm Stroke height 200 mm Mold height 272 mm Part height (positive and negative) max. 100 mm Number of strokes (infinitely variable) 25 - 130 /min Trimmed Parts are stacked through the Punch Tool The Skeletal Waste is fed directly into the Grinder ILLIG RS75 Under the Trim Press Grinder, Motor 8.3 kW, age 1995
Unwind Stand Preheater ILLIG VHW 72/ 2 ILLIG RDM 70K (refurbished in 2003) Thermoformer with auto-start facility Indramat Servomotor Indexing Top & Lower heaters Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Pneumatic Plug Assist, Max. Part height 125 mm Control Cabinet with Optimised Schleicher (PLC) Controls Auto Lubrication Pump. Inline ILLIG ÜG70B Counter/ Stacker, with delivery conveyor Inline Grinder & Blower
Unwind Stand Preheater ILLIG VHW 72/ 2 ILLIG RDM 70K, age 1989 Thermoformer with auto-start facility SEW Eurodrive Servomotor Indexing Max. material width 730 mm Max. Indexing length 300 mm Top & Lower heaters, total connected load top & bottom heaters 74.2 kW Drive Motor 6.93 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Hydraulic Plug Assist, Max. Part height 125 mm Hydraulic Power Pack Control Cabinet with Optimised Schleicher (PLC) Controls Encoder on Main Shaft Auto Lubrication Pump. Inline ILLIG UG70b Counter/ Stacker Delivery Conveyor for Counted/ Stacked Cups with Ejector Table
Used ILLIG RDK 54 Thermoforming Line, Age 1995 Unwind Stand Indramat Servomotor Indexing Max. Film width 610 mm max. Thickness range 0.18 to 2.5 mm. Hardened Transport Rails, Double Heating, Heating Load 41.0 kW. Heaters move forwards automatically with pneumatic control Sheet Sag Control Form Area 550 x 400 mm Forming & Punching in Mold with integrated Steel Rule Die. Positive Draw 20 mm, Negative Draw 20 to 40 mm Trimming Force 50kN. Top and Lower Platens Moved by separate Indramat Servomotors Heavy duty Toggles on both upper & Lower Platen Stacking/ Counting Station Waste Material Winder Inline ILLIG RS75b Grinder with Sound Proof Housing & Controls. Suitable for PS, OPS, PP, PE, PVC etc.
PS, K-Resin Lid Mold for the ILLIG RDM 58/ 3, dia. 120 mm, 8 Cavity, together with associated stacker Parts
Unwind Stand Preheater ILLIG VHW 72/ 2 ILLIG RDM 70K Thermoformer with auto-start facility Indramat Servomotor Indexing Top & Lower heaters Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Pneumatic Plug Assist, Max. Part height 125 mm Control Cabinet with Optimised Schleicher (PLC) Controls Auto Lubrication Pump. Inline ILLIG ÜG70B Counter/ Stacker, with delivery conveyor Inline Grinder
Due to a clearance sale this Machine is on Sale at a very special Price Inline ILLIG RDM 63/ 15d Thermoformer with: Auto unwind stand Auto Start System Servomotor Indexing Double heating, Sheet Sag Control Auto Rail Spreading for PP Plug assist Max. form area 750 x 305 mm Max. film width 770 mm Max. index 360 mm Max. depth of draw 150 mm Encoder on the Main Drive Shaft SCHLEICHER P-SK 2/ 126F Modern PLC Controller for Control of Form Air, Blow- off etc. Pneumatic Cylinders for automatically raising the Transport Rails after Forming Cycle. aids in removal of difficult Products from the Mold Separate Control Cabinet Machine is ready for PP
Illig deep drawing machine Type: UA 150, 14.500 h Runhour! Built: 1986 Closing unit Plate size: 1000 x 1500 Other max. plate size: 1000 x 1500 max. moulding area: 950 x 1450 max. Drawing depth: 600 UA 150 has upper heating small spotlight with 4 position circuit with separate control cabinet underheating has total field control, flat-fitting chip frame autom. Upper stamping system Normal construction with 2 downhill control film throughhang control Protective grille by hand 4 compartment cooling fan + 4 compartment spray nozzle cooling pre-blowers + automatic deforming, reduction frame - quick change device electron. Schleicher control in the separate control cabinet 1 clamping frame for max. mold ingescent
Three Illig punching machines are available for the precise punching of thermoformed plastic parts from film material. Working width: approx. 900mm, working height: approx. 120mm, roller diameter: approx. 196mm, machine dimensions X/Y/Z: approx. 2500mm/1300mm/1600mm, weight: approx. 750kg. Including two hydraulic punching machines Wolf EHPT 6E and two manual swivel arm punching machines. On-site inspection is possible.
An Illig thermoforming machine is available. Working dimensions X/Y: 500mm/400mm, max. air pressure: 10bar, heating power: 4.5kW, motor power: 1.24kW.
Age 2007, Consisting of :-, Siemens S7 PLC Controls Indramat Servomotor Siemens SINAMICS Motor Drive Rittal Control Cabinet Cooling Unit with Temperature Display With Snap -Stacking Brush Stacking Cascade Stacking The Counter/ Stacker is in v. good production, This ILLIG SZS73 was working Inline with a Generation 3 ILLIG RDM70K Line., Effective Working Area: 740 x 340 mm, Max. Part Height: 150 mm, Formed Part Stacking Length: 800 mm
