Hydraulic plate bending machine 4-roll capacity width 750x20 mm thickness Brand MG model EH0720 CNC year of make 2001 Bending capacity with dual Initial pinch planetary plate width 700 mm plate thickness 20 mm pre-bend 16 mm --- Length on the rolls 750 mm Upper roll 220 mm lower roll 200 mm side rolls 180 mm + 1 extra upper roll smaller size 175 mm interchangeable minimum achievable rolling ID 200 mm Power electric 10Hp voltage 380/50 Vac --- Installed configuration Hardened surface of the 4 rolls Driven rolls rotation hydraulic motorized with gear units Synchronized speed automatic between the rolls Re-rolling device for calibration roundness of welded shells Front open drop-end to unload the closed rolled plates Control console electric commands with CNC and digital readout CNC programmable automatic plate rolling – System WinME 4 axis Dig ...
nr. 1 Plate Bending Machine 3 roll planetary with pre-pinch plate width 750 x plate thickness 100 mm -brand MG Italy, model MG07100H year 1999. Bending capacity: Plate width: 750 mm Plate thickness: 100 mm Technical data: 480 mm upper roll 450 mm side rolls Supply voltage 3 phase 400/50 Vac -Power 37Kw on hydraulic power unit Configuration installed with the machine Hardened surface of the 3 rolls. Conical bending attachment hydraulic to roll cones 3 rolls driven with planetary gearbox and motor each roll independent Calibration system for the re-rolling and rounding welded shells Console electric on wheels with joysticks controls and digital readout. Opening front side hydraulic drop-end to unload closed shells. Variable speed working slow/fast. Emergency stop and safety systems in compliance with regulation. Add-on guide rings to keep alig ...
Limpet coil roller hydraulic to form half round pipe from flat metal strip and bending into wanted radius with spiral continuous. -Shafts output size 80 mm -Interchangeable set of rollers on the shafts for the different size of pipe -Coil holder for the reel metal strip with guide-way bench uncoiling and alignment the steel strip to the rolling machine -Pinching lower central roll adjustable to form the half pipe -Side roll with digital position readout to determine the bending diameter of the coil -hydraulic arm in 3 directions to set the pitch of the coil roll -Upper vertical support hydraulic operated to hold in position the formed diameter and collect the coils -Control panel electric with push buttons with digital position readouts for the coil length, the bending radius and the forming load. -Service manuals and operation books along with the machine. ...
Plate roll hydraulic variable axis 3 roll capacity 3100x 130 mm with pre-pinch Brand MG model PH3.1500 year 2016 machine in perfect condition as a new with warranty included top roll size 880 mm side rolls size 800 mm useful width 3100 mm Capacity Plate width mm. 3000 Rolling thickness mm. 130 Pre-bend thickness mm. 100 minimum rolling diameter 1000 mm (see capacity bending chart in enclosed ) electric power 150 Hp run the hydraulic unit variable axis rolls configuration with pre-bending -Rolls all the 3 are driven and synchronized with planetary gear unit and hydraulic motor each roll -Conical plate bending the 3 rolls are tiltable front-back special configuration for cones forming -Digital position readouts of the 3 rolls -friction free technology all movement on bearings -Overload safety hydraulic protection -Centralized operator panel elec ...
PLATE BENDING MACHINE FACCIN - 4 ROLL HYDRAULIC 3000 X 40 MM - MODEL 4HCI3-35/30 YEAR 1990 PLATE BENDING ROLL LINEAR GUIDEWAYS DOUBLE PINCH PRE-BENDING Machine in good working condition Bending capacity -Plate width : 3000 mm -Rolling plate thickness 40 mm - Prebend thickness 35 mm Rolls dimensions: -Useful length 3050 mm -central rolls upper/lower D 470 mm -side rolls left/right D 420 mm • Hardening of the 4 rolls high strength surface • 3 rolls driven powered with gear unit with hydraulic motor • Conical bending attachment side rolls tiltable to form cones, contrast pad roller type. • Opening front hydraulic drop-end to unload the closed shell. • Variable speed working roll bending rotation hydraulic speed fast/slow. • Conso ...
Hydraulic plate bending machine 4-roll capacity width 3000x20 mm thickness Brand MG model EH320 used machine year 2001 Bending capacity with dual Initial pinch planetary plate width 3000 mm thickness 20 mm pre-bend 16 mm minimum rolling ID 420 mm depending on plate thickness and strength. --- Length on the rolls 3100 mm top roll 350 mm lower roll 330 mm side rolls 250 mm Power electric 15Hp voltage 400/50 Vac --- configuration Hardened surface of the 4 rolls Dual driven central rolls rotation hydraulic motorized with gear unit each roll. Conical plate bend hydraulic attachment for cone bending. Re-rolling device for calibration roundness of welded shells Front open drop-end to unload the closed rolled plates Control console hydraulic commands with digital readout Digital position readout of side rolls Safety and emergency systems installed Manuals and s ...
Key data: 1250 mm, 3 mm, 3 mm
Plate bending machine 2-roll pinch total bend in one-turn. Make MG model PK12 1250 x 3 mm year 2004 Plate sheet max width 1200 mm Plate thickness up to 3 mm Machine fully hydraulic operated Hydraulic power unit with 5,5 kw electric motor Top roll size 100 mm Lower pinch roll size 300 mm urethane rubber coated Automatic rolling sequence Vertical support adjustable to the diameter to hold in place the round formed plate. Set of mandrel tubes 7 pieces interchangeable slip-on to change the rolling diameter Console electric commands for manual use and automatic programmable bending cycle Safety and emergency stop system installed Manuals and schematics along with the machine
Key data: 60
Profile bending machine hydraulic -output shafts size 250 mm Equipped with traction tooling for H-beam HEB IPE UPN capacity chart see enclosed model AR250 MG brand make year 2016 Configuration -pyramid dual pinch side rolls independent hydraulic -3 rolls driven hydraulic and gear units each shaft. -Rollers size 660 mm adjustable opening to seat and bend the profiles -set of rolls for HEB IPE up to 300 mm -flat bar 200 mm -square bar 125 mm -angle roll 200 mm legin / legout -Lateral correctors left/right side hydraulic operated in 3 directions -Traction tool hydraulic operated tensioning for HEB-IPE – UPN bending -Set of heads for tensioning HEB – IPE - UPN beam bending on the hard side -Add-on rollers angle bending & T-section leg-in / leg-out -Control panel console electric joysticks manual operate with Digital readouts -Electric power ...
Key data: 3100 mm, 40 mm, 32 mm
- 4 ROLL HYDRAULIC MODEL M3040 manufacture MG srl, year 2024 PLATE BENDING ROLL PLANETARY DESIGN DOUBLE PINCH PRE-BENDING MG NEW CONSTRUCTION Bending capacity -Plate width : 3000 mm -Rolling plate thickness 40 mm - Prebend thickness 32 mm minimum bending diameter ID 530 mm Rolls dimensions: -Useful length 3100 mm -top roll 450 mm -lower roll 410 mm Configuration installed with the supply: • Hardening induction treatment, high strength surface of the 4 rolls • Pre-bending operation with pinch pressure adjustable upon the plate thickness. • Powered driven both the central rolls with axial gearbox and direct drive hydro-motor. • Console electric on wheels with centralized commands joysticks and digital readout. • Digital readou ...
Key data: 3100 mm, 16 mm, 12 mm
3roll 3000x16 mm MG MODEL AK316 plate bending machine Surface width 3100 mm -Top roll 300 mm -Side rolls 270 mm -Power electric 10 Hp -Weight 8 ton Capacity -plate width 3000 mm -plate thickness 16 mm -pre-bend 12 mm Rolling diameter from 350 mm and above Configuration complete for use: -the 3 rolls hardened high surface strength -the 3 rolls driven hydraulic with axial planetary gear individual each roll synchronized rolling speed hydraulic automatic balance -conical bending attachment for cone bending -re-rolling system for seam welded shells -console centralized with hydraulic commands -Digital position readout to repeat bending with accuracy -Safety installations with emergency stop. -Manuals of instruction DIMENSION 4500X1300XH1500 MM Machine in very good conditions
Specifications: Working length: 4100 mm Max. bending power: 10.0 mm Bend: 8.0 mm Diameter upper roller: 310 mm Diameter of lower rollers: 285 mm Hardened rollers hydraulic snap roller bearing Conical bending device Control panel with digital display CE mark Dimensions (length x width x height)): approx. 5100 x 1250 x 1400 mm Weight: approx. 6.2 tons Condition: very good, almost mint condition The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.
Specifications: Working width: 1050 mm Max. bending power: 100.0 mm Max. bend: 80.0 mm Diameter upper roller: 530 mm Diameter of side rollers: 530 mm Conical bending device by inclined position of the two side rollers Mobile control panel with digital display Engine power: 37 kW Hydraulic Safety Chucks CE mark Net weight: approx. 16 tons Auxiliary: 2. Roller set : Diameter upper roller: 360 mm Diameter of side rollers: 360 mm
Hydraulic plate bending machine 4-roll capacity 2500x18 mm thickness Brand MG model MH2518 Year 2007 Bending capacity with pre-pinch plate width 2500 mm thickness 18 mm pre-bend 14 mm --- Max width on the rolls 2600 mm top roll size 280 mm lower roll 260 mm minimum bending rolling dia. Ø 330mm Power electric 15Hp voltage 380/50 Vac --- Installed configuration Hardened rolls, high surface resistance Driven central rolls rotation hydraulic with gear unit Rolls parallelism lifetime with torsion bar Pre-pinch pressure adjustable for best pre-bend Conical plate rolling hydraulic with contrast pad Drop-end top roll front hydraulic opening unload Re-rolling calibration system for welded shells Digital readout display position of rollers Safety and emergency systems installed Manuals and schematics originals Weight of the machine 7 ton
Hydraulic Plate Bending machine 3 roll 3000x220 mm planetary pinch pyramid model MG3220 3 roll year of make 2012 Capacity : Plate width mm. 3000 Rolling thickness mm. 220 Pre-bend thickness mm. 180 -3 rolls driven hydraulic motorized with axial gear unit on each roll independent -Synchronized hydraulic rotation of the 3 rolls with variable speed. -Planetary design with pre-pinch fully hydraulic -Digital position readouts of the bending rolls -Rolls installed on bearings double crown heavy duty. -Overload safety hydraulic operation protection of the 3 rolls -High pressure hydraulic power pack with multi-pumps oil feed -Power installed total 450 Hp voltage Vac 380/50 -Hydraulic reservoir 2500 liters of oil, Hydraulic oil chiller refrigerator, stand alone cooling system in automatic -Centralized console electric movable on wheels with joysticks and di ...
Three-roller calender brand MG 3000 x 200 mm. Year 2006
Key data: 200 mm, 300 mm, 200 mm
Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6 inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on wheels with all electric commands. -Dual rolling speed up to 5 mtr/min with automatic balancing system between the 3 rolls. -Safety devices in compliance with European regulation. CE mark. -e ...
4 ROLL HYDRAULIC MODEL 2500 X 35 MM MG BRAND MODELM2535 YEAR 2008 plate bending machine top roll 400 mm max plate width 2550 mm capacity thickness 35 mm prebend thickness 30 mm Technical data rolls hardened very high resistance conical plate bending attachment Console electric on wheels with centralized commands Digital position readout, NC controller programmable Opening front side hydraulic drop-end Rerolling system for welded shells rounding. Variable speed working fast/slow. Voltage 380/50 safety and emergency devices manuals along with the machine original
4 ROLL BRAND NEW MACHINE 2000X20MM -plate width 2000 mm -plate thickness 20 mm -prebend 14 mm -Top roll mm. 280 -lower roll mm. 260 -Power electric 380/50 Minimum rolling ID 330 mm Capacity 2000 X 20 mm Capacity 1000 x 25 mm -4 rolls hardened very high strength on surface -direct driven rolls rotation with axial planetary gear + hydraulic motor each roll. -conical bending hydraulic tilt angle for plate rolling conical reducers -rerolling system for welded plates to pass automatic welded seams thru -overload protection hydraulic safe operation. -console centralized with electric joysticks -rollers position bending and pre-bend digital readout CNC EVO graphic controller automatic fully programmable 4 axis plate rolling. Auto-calculate programs upon plate data input and test. .dxf files from cad station immediate drawing import and run bending program. ...
4 roll plate bending machine 3100 x 28 mm brand new year 2023 ready. MG model M3028 Capacity plate 3000 mm bending thickness 28 mm prebend 22 mm dual pre-pinch technical data: -length of rolls 3100 mm -top roll dia. 380mm -lower roll dia. 360mm - Power electric 20Hp weight 17ton Configuration fully hydraulic -Hardened surface of the 4 rolls , smooth finishing suitable for stainless steel plates rolling -Digital position readout with memory set -Conical bending plates , contrast pad hardened , rollers angle tiltable -Driven rolls hydraulic plate dragging with axial gear unit each powered rolls. -Opening front hydraulic to unload closed shells. -Rerolling system for welded plates calibration precise rounding. -Control console electric commands with digital readout -Safety installation and emergency stop according to regulation
4 ROLL HYDRAULIC MODEL 1000 x 22mm CNC EVO GRAPHIC 4AXIS PROG PLATE BENDING ROLL PLANETARY DOUBLE PRE-PINCH PLATE PRE-BENDING capacity: -Width of plate: 1000 mm -Thickness of plate rolling 22 mm -Thickness of plate pre-bending 16 mm minimum bending diameter ID 280 mm depending on the plate thickness vs. yield strength Rolls -Surface length mm. 1050 -top roll mm. 250 -lower roll mm. 260 -Power electric 15Hp on centralized hydraulic unit , voltage 3ph Vac 400/50 Configuration installed • Hardening of the 4 rolls , very high resistance against wear. • Central rolls both driven powered with axial gearbox and direct drive hydraulic motor. • Calibration system for the re-rolling of welded shells rounding unwanted flat spots. • Console electric on wheels with centralized commands joysticks CNC position r ...
3-roll hydraulic with dual pre-pinch planetary configuration. new to complete, 45 days from order. -Plate width 3000 mm -Capacity rolling plate thickness 50 mm -Pre-pinch plate thickness 40 mm Machine configuration and accessories installed: -useful surface length on the rolls 3100 mm -upper roll size 480 mm -lower rolls size 440 mm -Digital position readouts. -Hardening treatment of the 3 rolls. -3 rolls driven hydraulic motorized with independent axial gear box on each roll. -Conical plate bending attachment with tiltable lower rolls hydraulic. -CE quality certification, Made in Italy manufacturing. -Service manuals and operation instruction manuals. -Hydraulic diagrams -Electric & electronic schematics with parts list. -Set of service tools for maintenance. -Electric power installed 50Hp. -3 phase voltage to be specified Warranty 12 months. ...
Sheet thickness: 10,00 mm Bending length: 2050 mm Number of rolls: 4 Make MG 10 mm Type MH 2010 B Year 2009 4 walzen rundbiege plate roll blechrundbiege mg Sheet thickness (mm) T = 10 mm Bending length (mm) L = 2.050 Number of rolls Pre = 6 mm Top roll = 210 2 rolls driven Digital read out Hardened rolls 55 Hrc Fully hydraulic CE Saftety
Sheet thickness: 10,00 mm Bending length: 3100 mm Number of rolls: 4 Make MG 10 mm Type MH 308 B Year 2006 4 roll hydraulic plate bender mg blechrundbiege Sheet thickness (mm)T = 10 mm Bending length (mm)L = 3.100 mm Number of rolls 4 roll Pre bend = 6 mm Top rol = 230 mm Lower rol = 220 incl. Hydr. side support incl. CNC Control
Sheet thickness: 10,00 mm Bending length: 3100 mm Number of rolls: 4 Make MG 10 mm Type MH 308 B Year 2006 4 roll hydraulic plate bender mg blechrundbiege Sheet thickness (mm)T = 10 mm Bending length (mm)L = 3.100 mm Number of rolls 4 roll Pre bend = 6 mm Top rol = 230 mm Lower rol = 220 incl. Hydr. side support incl. CNC Control
Sheet thickness: 2,00 mm Bending length: 1050 mm Number of rolls: 2 SPECIFICATIONS Controll MG CNC Hydraulic / Mechanical Hyrdaulic 3 or 4 roll 2 Urethan Maximum sheet thickness 2 mm Bending length 1050 mm Top Roll Ø 100 mm Bottom Roll Ø 300 mm Power 5.5 kW
Sheet thickness: 10,00 mm Bending length: 2050 mm Number of rolls: 4 Make MG 10 mm Type MH 2010 B Year 2009 4 walzen rundbiege plate roll blechrundbiege mg Sheet thickness (mm) T = 10 mm Bending length (mm) L = 2.050 Number of rolls Pre = 6 mm Top roll = 210 2 rolls driven Digital read out Hardened rolls 55 Hrc Fully hydraulic CE Saftety
