Used alligator scissors in good condition - Blade length 406 mm - Electric motor 400 V, 4.0 kW - Knife opening max. 250 mm - Cutting capacity up to max 50 mm round bar The scissors have been checked and repaired by us We supply a second, unused knife set for the scissors The machine is immediately available and can be viewed and tested at our premises. More information at infoRecyclinganlagen.info
The machine in one is a used twin-shaft shredder. The machine has been used in recent years for pre-shredding old cables. The year of construction of the shredder can no longer be determined. A good 2 years ago, new electric motors and a new control cabinet with a revised control system were installed. The outlet is currently provisionally made of wooden boards, but can also be replaced or adapted by sheet steel if desired. The shredder is available from approx. mid-April 2025. Specifications: Drive: 2 x 15 kW, 400 V Rotor length: 850 mm Shaft spacing: 250mm Knife width: 65 mm Blade torque: 8,600 Nm Filling opening: 1.7 m x 1.2 m Weight, approx. 2,000 kg
Compact but extremely versatile cable recycling plant. The pelletizing plant has both a Z-classifier (Zigzag) for the separation of 1 mm heavy copper and a turbine mill for processing fine cables and data conductors. The system was only fed and used by hand with selected cables. The condition is correspondingly good. Specifications: Suitability: Cables, cut to length without impurities Throughput capacity max. 150 kg/hour Connected load: 19 kW Dimensions (LxWxH): 1.4 m x 0.7 m x 2.3 m Weight: 1,200 kg Further information: infoRecyclinganlagen.info
The JMC 407 is the top seller among our alligator scissors. It is cost-effective, has a sufficient blade length and enough power for most metal recycling tasks. It is suitable for cutting many materials, such as profiles, pipelines, motors, cables or gearbox housings. The shears are also often used for cleaning scrap metal or cutting vehicle radiators. The machine has a control system without electronics and a manually adjustable hold-down device, which also acts as a protective cover. Using the foot pedal, the scissors can be used in single or continuous operation. The opening width can be adjusted using simple clamping screws. The scissors are from our demonstration pool and can of course be viewed or tested. Further information at BPS Recyclinganlagen GmbH at infoRecyclinganlagen.info
Universally applicable alligator shears for almost all areas of application in scrap metal operations. Fast, powerful and robust. Specifications: Knife caps: 406 mm Cutting cylinder force: 106 tons Cutting speed, max: 60 cuts/minute Weight, approx: 1,000 kg Operated by foot pedal Single cut or endurance run Further information: infoRecyclinganlagen.info
Strong alligator scissors with longer blades - ideal for radiators and trays. The Deltax DTX 4/600 not only has longer blades than its little brother, but also a higher cylinder force. The hold-down device can be securely locked at different heights and does not slip upwards during operation. The scissors are also available in the CAT version with an additional push-on aid. Specifications: Blade length: 610 mm Max. opening width of the blades: 318 mm Cutting pressure of the knife: 110 tons Drive: 7.5 kW, 400 V Cutting speed, max: 60 per minute For more information, see infoRecyclinganlagen.info
Heavy alligator scissors with maximum cutting power. The Deltax DTX 600 offers the unique hydraulic hold-down device that lowers parallel to the lower knife. This keeps the round material and material shaft secure. Nothing slips out to the front. This means that several bars or profiles can be processed safely in one go. Specifications: Blade length: 610 mm Cutting force: 172 or 210 tons cylinder pressure Opening width: 330 mm Drive: 11.0 kW, 400 V More information at infoRecyclinganlagen.info
It is a unit for cutting open catalysts and removing the ceramics. It comes from a lease return and is unused. The hydraulic shear has the extension for opening the interfaces compressed interface. There is also a hydraulic hold-down device for holding other materials, such as profiles or sheet metal. The connection for a dust extraction system is also available on the Catmate. The scissors come from the manufacturer JMC/Mc Intyre, the operation is via a foot pedal as a single cut or in continuous operation. Blade length : 508 mm Knife opening: 255 mm at the tip Cutting cylinder: 120 tons Dimensions, ( L x W x H ) approx. : 1.7 x 0.9 x 15 mm Weight: 1150 kg Drive: 7.5 kw / 400 V The unit is available for immediate delivery and can be viewed, tested and picked up from us in Weimar. For more information, see infoRecyclinganlagen.info
Used cable pelletizing system for mixed and stranded cables. The machine has been overhauled and equipped with new tools. The turbine was re-mounted and the control panel was replaced. In addition, the material inlet control has been activated so that the machine can be used automatically. The hourly output depends on the cable up to approx. 250 kg/hour when using a 5 mm sieve insert. The attached video shows the system in combination with the dosing tank and plastic loading. These components can be supplied as an option. It is operated via a 63 amp connection at 400 V. The power consumption is 28 kW. The plant can be visited and tested at our premises. More information at infoRecyclinganlagen.info
Used shredder for the pre-shredding of old cables and other materials. Cutting unit with knife blocks instead of cutting crowns. Two stator knives arranged opposite each other for higher hourly output. Easy-to-reach maintenance areas. Drive with 2 electric motors with 7.5 kW, 400 V each and a reduction gear arranged directly on the rotor axis. Hydraulic slide valve with load control. Rotor reverses in case of overload. A gearbox replaced. Perforated sieve 25 mm. Additional set of rotor blades. Output approx. 200 kg of cable per hour. The machine can be viewed and tested with us. Write to us. infRecyclinganlagen.info.
Overhauled hydraulic shears with new blades, seals, etc. With strong 0 t cutting cylinder. Perfect for demolition or recycling or as cable cutters in cable recycling. The shears can be operated via an electric or gasoline-powered hydraulic pump. The scissors are the reinforced industrial version and not a lighter rescue scissors. The scissors can be viewed and tested at our premises.
This BA 40.30 granulator was part of a cable recycling plant. These granulators were used by Tecnoecology and MG Recycling. With a rotor length of 400 mm and a diameter of 300 mm, the granulator can handle up to about 500 kg/hour of old cables. The granulator has its own control box with control panel and can therefore also be used standing alone. The granulator comes with several sieves and knife sets.
Machine for the processing of mixed waste cables, especially with fine conductors and stranded cables, The plant was most recently used for the post-cleaning of residual plastics from other cable recycling plants. Thanks to the rotor system with the 24 knife segments and the large flywheel masses, the system is also suitable for manual operation. The machine has a cooling unit that optimizes the granulator with a flow temperature of 0.5 °C for the use of heat-sensitive cables, such as NYM, etc. The control electronics of the system enable fully automatic operation in a line with pre-shredder, conveyor belt, dosing accumulator, etc. The machine includes several sets of knives and different sieves. In conjunction with a suitable pre-shredder, the system can process up to approx. 250 kg of old cable. The system was completely overhauled by us and equipped with new tools and par ...
Used and refurbished turbine mill from Tecnoecology for the digestion of old cables, especially fine strands or computer cables. Balling takes place at about 3,000 rpm. The tools are rotatable and have 4 usable edges. The turbine mill can be operated stand-alone or integrated into an existing system without a pellet mill. The machine has a 20 kW drive and can process up to approx. 300 kg of material per hour.
Machine for processing mixed old cables including fine conductors and stranded cables, Due to the special rotor system and the large flywheel masses, the system is also suitable for operation in manual insertion. The machine is equipped with a cooling unit that optimizes the granulator with a flow temperature of 0.5 °C for the use of heat-sensitive cables, such as NYM etc. The control electronics of the system enable fully automatic operation in a line with pre-shredder, conveyor belt, dosing accumulator, etc. The machine includes several sets of knives and different screens.
Small but very robust and powerful shredder for a wide range of tasks such as old cables, plastics, wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connections for connecting a cooling unit (e.g. when used for old NYM cables. The machine is and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.
The JMC 407 is the top seller among our alligator claws. It is cost-effective, has sufficient knife length and enough power for most metal recycling tasks. It is suitable for cutting many materials, such as profiles, piping, motors, gearbox housings. The scissors are also often used for cleaning scrap metals or cutting vehicle radiators. The machine is equipped with a control system without electronics and a manually adjustable hold-down device, which also acts as a protective cover. By means of a foot pedal, the scissors can be used in single or continuous operation. The opening width can be adjusted by means of simple clamping screws. The scissors are from our demonstration pool and can be viewed or tested.
Large Four Shaft Shredder with Two Cutting Shafts and Two Feed Shafts. Until now, the shredder has been used as a pre-shredder for the recycling of old cables. Due to the hydraulic tamper, the shredder can also be used for bulky materials. Changing the screens is hydraulically assisted and therefore easy to do. On request, the shredder can also be supplied with the articulated conveyor belt shown here. The conveyor belt is equipped with a magnet in the upper pulley for iron separation.
Used, heavy and high-performance recycling plant for the recycling of old cables. The machine has a granulator with a knife length of 500 mm and a large cutting table. As a result, the Sincro 530 from Guidetti achieves hourly outputs of 450 to 600 kg (manufacturer's specs). The system was traded-in by us and all essential components were checked in the workshop. The machine works reliably and trouble-free. On request, the system can be equipped with pre-shredders and conveyor belts. Feel free to visit us and get your own impression of the machine. You are also welcome to test the machine with your cable material.
Small dosing accumulator with screw conveyor for cable recycling plants, wood chips, etc. Capacity approx. 650 litres or 400 - 500 kg of pre-shredded old cable Adjustable conveying speed with frequency converter/inverter 0 - 16 rpm Drive only 0.55 kW with reduction gear Discharge height approx. 750 mm Dimensions (LxWxH): 2,200 mm x 800 mm x 1,800 mm Mobile via large heavy-duty castors with brakes
Used single-shaft shredder for wood, plastics, old cables, etc. Of course, the machine has received new knives and has been checked by us. Accordingly, we give 3 months of used machine warranty. The shredder has the amplified 30 kW drive (normally 15 kW) and is therefore enormously powerful. The rotor stops in the event of overload or blockage and reverses automatically. The hydraulics of the machine are dry, there are no leaks. Currently, a screen with a hole diameter of 14 mm is used, so that it is perfect for old cables. Of course, other screens in the range of 10 mm to 60 mm can also be used. The shredder is immediately available and can be viewed and tested. Further technical data: Rotor length: 630 mm Rotor diameter: 250 mm Feed travel: 600 mm Loading opening: 1,100 x 1,100 mm Drive rotor: 30 kW Drive hydraulics: 1.5 kW Rotor speed approx.: 90 rpm Weight ...
Used vibrating vibrating screen with two sieve inserts for three fractions. The sieve was used for the post-cleaning of plastic granules from cable recycling. The lower deck has an additional perforated plate with anti-clogging cleaning balls. The screen comes with inserts of 0.8 mm, 1.3 mm and 2.3 mm.
Simple unit for transporting plastic granules, such as PVC from cable recycling. Suction through hopper and 100 mm flex tube. Forwarding by fan/fan in rotary valve for dust removal. By extending the pipes, the unit can also be located further away from the feeding point. The big bags are suspended by height-adjustable chain hooks. The unit consisting of a rotary valve and filter is also adjustable in height. Of course, boxes can also be used instead of big bags. The machine can be inspected and tested with us.
Heavy conveyor belt for the recycling of old cables or other materials. The 30 cm strap is designed with concealed lateral pleated bars so that no wires or other material can get stuck in the gaps. The 0.75 kW drive motor is also equipped with a reduction gear, which significantly reduces the conveying speed. The conveyor belt is only used a little and therefore shows hardly any signs of wear.
Very good machine from our demonstration pool. Few hours of operation or signs of use. The peeling machine is suitable for XLPE cables, underground cables, cables with steel armouring, cables with aluminium and lead armouring, but also for processing PVC and rubber cables. With this machine, two cuts can be made at the same time in one operation, so that the processing can be twice as fast as with other models. Technical data: Working range/cable diameter: 30 mm to 150 mm Pulling speed: max. 12 m/min Motor: 2x 3.0 kW - 400 volts Dimensions (LxWxH): 1.8 x 1.0 x 1.2 m Weight: approx. 660 kg
Used overband magnet with new conveyor belt, new geared motor and new bearings. Length, strap 1,200 mm, magnet 700 mm Strap: width 300 mm, 5 studs Drive: 400V, 0.18 kW Aluminum frame with 4 eyebolts for suspension.
Cable recycling plant with many innovations in all plant components for up to 600 kg/hour (depending on material) The basis of this recycling plant is modularly constructed from strong and innovative individual components. In the standard version, the following structure is obtained. - Preshredder MR 4080 or MR 40-100 - Conveyor belt with magnetic separator - controlled by PLC - Granulator C 600 with axle length 600 mm, 5 rotor blades and 37 kW drive, cooling of the housing by unit against adhesions - Z-separator for the separation of heavy copper or 1 granulate - Dosing drum for the optimally uniform feeding of the following turbine mill - Ghibli 545 turbine mill (new model), optionally with coolable housing and inverter control - SA 600 separation table, new version with PLC inverter control of the air volume + eccentric drive with inverter control of the oscillation + adju ...
Young used machine with very few hours of operation. Compact cable recycling plant with low connected load for 80 - 120 kg/hour (depending on material) This system can be operated with a pre-shredder via a conveyor belt as well as in direct insertion. The system still has the original, unground set of knives, so it can hardly have more than 40 to 50 operating hours. Therefore, we offer this system including a 12-month used machine warranty. Pre-shredders, conveyor belts, dosing accumulators, etc. can also be obtained from us.
Used cable recycling plant Tecnoecology T 250 Turbo Year of construction: 2008 The plant consists of the following parts: - Pre-shredder: Bano MAC 630, approx. 250 - 400 kg/hour, depending on material - Conveyor belt to the dosing accumulator, approx. 4.0 m - Dosing accumulator with discharge conveyor, approx. 1.5 m³ - Controlled conveyor belt with belt magnet for feeding the granulator, approx. 4.0 m - Granulator GA 400/30, approx. 250 - 400 kg/hour, depending on material - Turbine mill, T 25-2, built in 2019 - Separator TV 300, inverter controlled, separation table 80 μm - Dust extraction and filter system The entire system currently achieves between 200 and 300 kg/hour in operation, depending on the cable composition. On request, additional components, such as a big bag loading for the plastic or the re-screening of the granules, can be supplied. The plant is curre ...
Used conveyor belt, built in 2020, few operating hours Very heavy design for recycling With very strong neodymium magnet in the upper deflection drum Reducing gear for slow conveying speed With concealed wavy edge and crossbars on the harness Large inlet hopper with adjustable slider for material height on the belt 4 m long, discharge height approx. 2.2 m (variable) Ideal, for example, for feeding material into a cable recycling plant At call
