Baler Paal Likon 80/60, built in 2004, very good condition Specifications: Manufacturer: Paal Type Likon 80/60 Year of manufacture 2004 Pressing force 60 t Drive power 75 kW Total power 94 kW Filling opening 1600 x 920 mm Bale dimensions 800 x 1000 mm, length variable 4-fold automatic tying Throughput 320 m³/h Throughput at 65 kg/cbm approx. 21 t/h Bale weight 660-1100 kg Transport dimensions approx. 9405 x 2200 x 2500 mm (LxWxH) Machine weight approx. 13 t Accessories: Funnel Version with a 520 l pump, drive 75 kW, for an increase in power to approx. 320 cbm/h under operating conditions, including oil cooling. Materials: paper, cardboard, foil, wood fibers, etc. The operating instructions and EC declaration of conformity are available in German. Remark: The machine is in very good condition. It was inspected and tested by us in 28816 Stuhr. You can find ...
Maximum pressure: 50 tons Year of Make: 2006 Pressing force: 7.14 kg/cm² Number of bindings: 3 horizontal Channel cross-section: 1000 x 700 mm Dimensions of the tailgate: 1250 x 950 mm Bale weight: do 500 kg Weight: approx. 10 tons Power connection: 400 V/ 22 kW Bale tying: automatic
Paal baler PGS 6540V - 65 tons of pressure - length 8800 width 2000 height 4700 - adjustable beam, width 1100, height 75 - Charging opening 1400x1020 - 4x vertical binding - 45 kW motor
Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2005 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 3,100 mm horizontally underfloor, then rising below 28° over a length of approx. 6,000 mm, Descending below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec. Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with lateral 20 mm high T-studs for sealing the be ...
Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1750 Year of Make: 2004 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 4,300 mm horizontally underfloor, then increasing over a length of approx. 6,300 mm, Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 1,027 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers, - Belt routing in a neutral zone to avoid stretching tensions, - Chain type M-80 with case-hardened bushings, bolts and roller ...
Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2009 specifications: Conveying width: approx. 1,500 mm Center distance: approx. 9,625 mm Belt course: approx. 3,000 mm horizontally running underfloor, then rising below 30° over a length of approx. 5,875 mm, sloping below 20° on the remaining length and conveying into the press Conveyor belt drive power: 3.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers, ...
used baler Manufacturer: PAAL Type: LIKON 110/150 Year of construction: May 2004 Specifications: Press weight up to: approx. 36 tons Press force at 275 bar: 150 t Operating pressure max. 320 bar Filling opening: approx. 2,000 x 1,020 mm Channel cross-section: 1,100 x 1,100 mm Drive power: 2 x 75 kW Flow rate: 425 m³/h Binding: 5-fold horizontal Total connected load: 176 kW Rated current: 340 A Pre-fuse (min.) 400 A Operating voltage: 3 x 400 VAC/50 Hz/N/PE Control voltage: 230 VAC / 24 VDC including: - Oil cooling - Low-pressure circuit - Free kicks - Key locking system Transport dimensions: Length: 13,803 mm Width: 2,500 mm Height: 3,164 mm without wire unwinding devices, without binding wire, without feed belt, without a personal protection system, without conveyor belt hopper and withou ...
Fully automatic baler Manufacturer: PAAL Type KONTI 275 D Year of Make: 2000 specifications: Press force: 75 t Drive power: 1 x 45 kW Total connected load: kW __ / 170 A Throughput under operating conditions: 280 m³/h Filling opening: 1,020 x 1,550 mm Bale size:750 x 1,100 mm Binding: 4-fold vertical incl. front printing plate slot cover Machine weight: approx. 25 t Bale weights: up to approx. 600 kg Including: - Free kicks - Large digit display
Specifications Maximum pressure: 85 tons Year of Make: 1994 Pressing force: 103 tons/m² Number of ties: 4 - vertical Channel cross-section: 750 x 1100 mm Dimensions of the tailgate: 1020 x 1750 mm Bale weight: 500-650 kg Weight: 26 tons Power connection: 400 V/ 55 kW Bale tying: automatic
Baler Paal Pacomat II-50 C, built in 2015 Specifications: Manufacturer: Paal Type Pacomat II-50 C Year of construction 2015 Pressing force 50 t Drive power 45 kW Filling opening 1200 x 620 mm Bale dimensions 700 x 1000 mm, length variable 4-fold automatic tying Throughput at 35 kg/m³ approx. 6.7 t/h 60 kg/m³ approx. 10.6 t/h Bale weight up to 500 kg Transport dimensions approx. 7300 x 2000 x 2500 mm (LxWxH) Machine weight approx. 8500 t Materials: paper, cardboard, foil The press is in good condition. It was only used for waste paper / die-cutting residues. The complete documentation including CE declaration, electrical circuit diagram and hydraulic diagram is available in German. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subject to change, su ...
automatic baler Manufacturer: PAAL Type: KONTI 600 F Year of construction 2016 specifications: Press force: 1546 N Specific pressing force: 128 N/cm² Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 3 x 55 kW Throughput: up to 805 m³/h with a bulk density of 35 kg/m³ Capacity at 35 kg/m³: 28.0 t/h Capacity at 60 kg/m³: 45.5 t/h Capacity at 100 kg/m³: 64.5 t/h Binding: 5-fold vertical + 4-fold horizontal Bale weight: approx. 800 - 1,250 kg depending on baled material and bale length Machine weight: up to approx. 42 t
automatic baler Manufacturer: PAAL Type: KONTI 600 F/k with cross-binding Year of construction 2008 Machine was only in operation for 4 years specifications: Press force: 145 t Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 2 x 75 kW Throughput capacity:approx. 510 m³/h Capacity at 35 kg/m³: 17.5 t/h Capacity at 60 kg/m³: 30.0 t/h Capacity at 100 kg/m³: 47.0 t/h Binding: 5-fold vertical Additional 4-fold automatic horizontal bonding Bale weight: approx. 800 - 1,250 kg depending on baled material and bale length Machine weight: up to approx. 42 t Attached pictures are only sample pictures!
automatic baler Manufacturer: PAAL Type: KONTI 600 F Year of construction 2009 Operating hours: only approx. 22,000 specifications: Pressing force: 150 t at 300 bar Specific pressing force: 124 N/cm² Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 2 x 45 kW Throughput: approx. 375 m³/h Capacity at 35 kg/m³: 13.0 t/h Capacity at 60 kg/m³: 22.5 t/h Capacity at 100 kg/m³: 35.0 t/h Binding: 5-fold vertical Bale weight: approx. 800 - 1,250 kg depending on baled material and bale length Machine weight: up to approx. 45 t
Baler Paal Pacomat II with hopper, built in 1979 Specifications: Manufacturer: Paal Type: Pacomat II Year of Make: 1979 Drive power: 11 kW Pressing force: 27 t Channel cross-section: 700 x 1000 mm Filling opening: 1000 x 650 mm Flow rate: approx. 60/115 m³/h Bale size: 700 x 1000 mm Bale weight: up to 400 kg Machine dimensions: approx. 7000 x 2000 x 2000 mm (LxWxH) Machine weight: approx. 5200 kg Materials: paper, cardboard, foil Remarks: The machine is in working condition. It was inspected and tested by us in 28816 Stuhr. You can find the video on our website or our Youtube channel. Viewings, also under power, are possible at any time by arrangement. On request, we also carry out tests with your material for an expense allowance. We will also be happy to answer any questions you may have about the machine by phone from Monday to Thursday from 08.00 to 14.00 ...
used baler Manufacturer: PAAL Type: PACOMAT I-35 Year of Make: 2008 specifications: Press force: 35 t Specific pressing force: 7.14 kg/cm² Drive power: 22 kW Throughput: up to approx. 85 m³/h under operating conditions Channel format: 700 x 700 mm Filling opening: 800 x 620 mm Machine weight: up to approx. 6.5 t (depending on equipment)
automatic baler Manufacturer: PAAL Type: KONTI 125 Year of Make: 1988 Operating hours: approx. 23660 specifications: Press force: 40 t Specific pressing force: 5.7 kg/cm² Channel format: 700 x 1,000 mm Binding: 3-fold vertical Bale weight: 375 - 450 kg, depending on material and bale length Filling opening: 1,400 x 920 mm Machine weight: approx. 10 t Drive power: 22 kW Throughput: approx. 115 m³/h Pressing capacity: approx. 4.00 t/h at department store (35 kg/m³ bulk weight) approx. 6.75 t/h for mixed paper (60 kg/m³ bulk weight) approx. 10.0 t/h for collected goods (100 kg/m³ bulk weight)
Specifications Maximum pressure: 75 tons Press force: 90.9 t/m² Channel cross-section: 750 x 1100 mm Bale weight: 500-750 kg Power connection: 400 V Year of Make: 1999 Number of bindings: 4 vertical Dimensions of the tailgate: 1020 x 1550 mm Weight: approx. 25 tons Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the channel. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the bale chamber for easy maintenance
Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of construction: 2008 specifications: Conveyor width: approx. 1,500 mm Wheelbase:approx. 9,625 mm Strip course: approx. 2,935 mm horizontally underfloor, then rising to a length of approx. 4,500 mm below 28°, sloping below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE as far as possible pre-assembled, consisting of: - Strip scaffolding in solidly welded section steel and sheet steel edge construction, - additional sliding guides underneath the belt support profiles in the horizontal and climbing sections to support heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with 2 ...
Sliding belt conveyor Paal, type W GUH-1200, built in 2004, usable width 1200 mm, total length approx. 10,500 mm Specifications: Manufacturer: Paal Type W GUH-1200 Year of construction: 2004 Drive power: 4 kW Overall length: 10,500 mm Sidewall height: 550 mm Overall width: 1,630 mm Belt width: 1,200 mm Gradient: variable Total height: 1,600 mm Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offers are subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sale takes place from the location, without guarantee and guarantee. Our payment term is 100% prepayment.
used baler Manufacturer: PAAL Type: CPH 6540 Machine number: 29600 Year of construction: 2008 Main parts of the press: 1 automatic channel press 1 automatic lacing 1 hydraulic system 1 electrical control Press force at approx. 300 bar: 650 kN Duct cross-section (h x w): 75 x 100 cm Filling opening (l x w): 160 x 92 cm Number of binding wires: 4 pieces Power: - Wire pull: 3 kW - Twisting: 3 kW - Main drive pump: 75 kW Hydraulic oil tank volume: 2200 l Machine weight: approx. 14 t, depending on equipment Operating voltage: 3 x 400 VAC / 50 Hz / N / PE Press complete for continuous operation including: Machine design consisting of: - Pressure plate with roller guide mounted on the inside at the bottom, - Press box floor made of highly wear-resistant special steel, - replaceable, screwed running dies for the lower pr ...
automatic baler Manufacturer: PAAL Type: KONTI 275 D Year of construction: 2002 Operating hours: approx. 30,000 hours Main parts of the press: 1 automatic channel press 1 automatic lacing 1 hydraulic system 1 electrical control specifications: Press force: 75 t at 300 bar Specific pressing force: 9.09 kg/cm² Duct cross-section (h x w): 750 x 1,100 mm Filling opening: 1,020 x 1,550mm Number of binding wires: 4 pieces vertical Drive power: 1 x 75 kW Throughput: up to approx. 350 m³/h Hydraulic oil tank volume: 2,200 l Operating voltage: 3 x 400 VAC / 50 Hz / N / PE Other features: - Automatic cutting edge release - Large digit display for bale length and fault indication
automatic baler Manufacturer: PAAL Type: KONTI 275 C Year of construction 1996 specifications: Press force: 65 t Specific pressing force: 7.88 kg/cm² Channel format: 750 x 1,100 mm Bale weight: 450 - 600 kg, depending on material and bale length Filling opening: 1,550 x 1,020 mm Drive power: 45 + 30 kW Throughput: 380 m³/h Pressing capacity: - approx. 13.0 t/h at department store (35 kg/m³ bulk density) - approx. 23.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 35.0 t/h for collected goods (100 kg/m³ bulk density) Setting: 4-fold vertical Machine weight: approx. 21.0 t Optionally with feeding belt according to photos
automatic baler Manufacturer: PAAL Type: KONTI 200 C Year of construction: 1993 specifications: Press force: 50 t Channel format: 750 x 1,100 mm Specific pressing force: 6.06 kg/cm² Bale weight: 425 - 550 kg, depending on material and bale length Infill opening: 1,400 x 1,020 mm Drive power: 45 kW Throughput: 200 m³/h Pressing capacity: - approx. 7.35 t/h layered at department store (35 kg/m³ bulk density) - approx. 12.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 20.0 t/h for collected goods (100 kg/m³ bulk density) Setting: 4-fold vertical Machine weight: approx. 17 t
automatic baler Manufacturer: PAAL Type: KONTI 600 G/S/K with cross-binding Year of construction 2012 Operating hours: approx. 44,700 hours specifications: Press force: 1,546 kN System pressure: 315 bar Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 3 x 55 kW Pump capacity: 3 x 420 Ltr. Oil tank volume: 3,100 ltr. Throughput:approx. 780 m³/h Capacity at idle: approx. 1,220 m³/h Capacity at 35 kg/m³: approx. 26.5 t/h Output at 60 kg/m³: approx. 44.0 t/h Output at 100 kg/m³: approx. 69.0 t/h Control: Siemens S7 Setting: 5-fold vertical Additional 4-fold automatic horizontal tying Bale weight: approx. 800 - 1,250 kg depending on the material to be pressed and bale length Machine weight: up to approx. 42 t Includes a top pressure plate slot cover Printing plate was renewe ...
Baler Paal Likon 80/60, built in 2004, very good condition Specifications: Manufacturer: Paal Type Likon 80/60 Year of construction 2004 Hours 13265 Press force 60 t Drive power 75 kW Total power 94 kW Filling opening 1600 x 920 mm Bale dimensions 800 x 1000 mm, length variable Setting 4-fold automatic Throughput 320 m³/h Throughput at 65 kg/cbm approx. 21 t/h Bale weight 660-1100 kg Transport dimensions approx. 9405 x 2200 x 2500 mm (LxWxH) Machine weight approx. 13 t Version with a 520 l pump, drive 75 kW, for an increase in power to approx. 320 cbm/h under operating conditions, including oil cooling. Materials: paper, cardboard, foil, wood fibers, etc. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is subject to change, subject to prior sale ...
Specifications Maximum pressure: 50 tons Press force: 7.14 kg/cm² Duct cross-section: 1000 x 700 mm Bale weight: do 500 kg Power supply: 400 V/ 30 kW Number of ties: 3 horizontal Dimensions of the tailgate: 1250 x 950 mm Weight: about 10 tons Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the duct. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the press chamber for easy maintenance
Specifications Maximum pressure: 65 tons Pressing force: 84 tons/m² Duct cross-section: 1000 x 750 mm Bale weight: do 550 kg Power supply: 400 V/ 45 kW Year of construction: 2011 Number of ties: 4 vertical Dimensions of the tailgate: 1400 x 920 mm Weight: approx. 13 tones Bale tying: automatic
Specifications Maximum pressure: 50 tons Power supply: 400 V/ 45kW Bale tying: automatic Press force: 7.14 kg/cm² Dimensions of the tailgate: 620 x 1050 mm Year of construction: 2020 Number of ties: 4 horizontal Duct cross-section: 700 x 1000 mm Bale weight: approx. 500 kg Weight: approx. 8.5 tonen Theoretical throughput to density 35kg/m3: 8.5 tons/hour Theoretical throughput to density 50kg/m3: 11.6 tons/hour
Specifications Maximum pressure: 50 tons Power supply: 400 V/ 45kW Bale tying: automatic Press force: 7.14 kg/cm² Dimensions of the tailgate: 620 x 1200 mm Year of construction: 2015 Number of ties: 4 horizontal Duct cross-section: 700 x 1000 mm Bale weight: approx. 500 kg Weight: approx. 8.5 tonen Theoretical throughput to density 35kg/m3: 6.7 tons/hour Theoretical throughput to density 50kg/m3: 9 tons/hour Press capacity: max 190 m³/h
automatic baler Manufacturer: PAAL Type: PACOMAT III 50 C Operating hours: approx. 1,750 hours Year of construction: 2014 Specifications: Press force: 485 kN (50 t) Specific pressing force: 6.4 kg/cm² System pressure: 315 bar only free kicks Drive power: 22 kW Total connected load: 92 kW, 175 A Throughput at idle: approx. 285 m³/h Throughput under operating conditions: approx. 125 m³/h Output at 35 kg/m³: approx. 4.4 t/h Capacity at 50 kg/m³: approx. 6.0 t/h Filling opening: 1,200 x 920 mm Duct format: 750 x 1,000 mm (H x W) Oil tank volume: 1,250 ltr. Control: Siemens S7-300 Machine dimensions: approx. 8,000 x 2,000 (4,100) x 2,460 mm (L x W x H) Machine weight: up to approx. 12 t
