Model
(Manufacturer: RAS)
Key data: 3 mm, 275 kg
used beading machine with electrical defect, hardware in good condition Description and order available. New price currently EUR approx. 16,000 without warranty I can only estimate operating hours at about 2000
Rok produkcji: 2007 Waga: 20,000 kg Maksymalna długość robocza: 2560 mm Maksymalna grubość blachy (stal miękka): 2.0 mm Maksymalna grubość blachy (stal nierdzewna): 1.5 mm Maksymalna grubość blachy (aluminium): 3.0 mm Dodatkowe wyposażenie: podajnik wykrojów, narzędzia
Key data: 2500 mm, 2 mm
with foot switch, with simple control up to 6 bending angles, potentiometer preset, manual bending beam lowering, Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 2500 mm Sheet thickness steel: 2.5 mm without backgauge Colour: green Total power requirement: 16 A Space requirement: approx. 3400 x 1000 x 1600 mm Machine weight: 2000 kg without roller scissors Bending angle: 145 degrees Machine Number: 50/3
Gr. working width: 1250 mm for sheet metal up to: 1.75 mm Opening width upper beam: 70 mm Adjustability bending brace: 50 mm Space requirement: 1880 x 740 x 1140 mm
Specifications: Working length: 4060 mm Bending capacity: 3.0 mm Control with bending simulation: MULTIBEND 901 grafik 2D Automatic adjustment of the bending angle depending on material thickness Bending angle adjustment: 0 – 180° Backgauge motorized adjustable: 10 -1500 mm Max. opening bending beam: 300 mm Bending and lower beam adjustment range : 80 mm Motor power: 7.5 kW Dimensions (length x width x height): approx. 5500 x 4050 x 2600 mm Weight: approx. 6.8 tons
Max. sheet thickness: 1.5 mm steel 2 transit stations Weight: approx. 500 kg
Key data: 2540 mm, 3 mm
Max. cutting length: 2540 mm Max. sheet thickness: 3 mm steel Manually adjustable backgauge from the front up to 550 mm Side stop and table extensions Sheet metal hold-up Knife sharpened Weight: approx. 2500 kg
Key data: 2540 mm, 2 mm
Max. cutting length: 2540 mm Max. sheet thickness: 2 mm steel Manual backgauge adjustable from the front up to 550 mm Pneumatic sheet hold-up Knife sharpened Weight: 1600 kg
Key data: 3100 mm, 2 mm
with manual backgauge 750 mm and sheet metal holding system, cut-down diverter for sorting the parts to the front or rear, plastic-coated hold-down device with single stroke and continuous stroke, very flat cutting angle of only 0.8 degrees for low-torsion cutting Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 3100 mm Sheet thickness steel: 2.0 mm Total power requirement: 3.0 kW Machine weight: 1950 kg Dimensions: 3750 x 1650 mm Machine number: 21/3
3-roll round bending machine with wire inserts Folded groove Colour: grey Shaft diameter: 55 mm Power: 1520x0.75 mm Dimensions: 1900 x 550 x 1110 mm Weight: 190 kg Machine number: 324/19 Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out
Key data: 3200 mm, 2 mm
with segmented upper beam H = 110 mm CNC control with motor depth stop Back gauge approx. 1000 mm 3200x2.0 mm, 3.0 mm aluminum, 1.25 mm front Colour: grey Total power requirement: 16 A Motor power: 2.2 kW Opening width: 200 mm LZ: 6 - 8 weeks, machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out.
Key data: 2040 mm, 3 mm
Max. cutting length: 2040 mm Max. sheet thickness: 3 mm steel Manual backgauge can be operated from the front up to 500 mm Side stop and table extensions Pneumatic sheet hold-up Knife sharpened
used
Round bending machine RAS 41.10 Working width 1020 mm Sheet thickness: 1.25 mm Weight 150kg
Key data: 1020 mm, 1 mm
Press brake, Manufacturer: RAS, Type: 61.10, Machine number: 265/9, Weight: 220 kg, Working width: 1,020 mm
Machine Type: Guillotine Shears Manufacturer: RAS Model: 54.30 Year of construction: 1975 Condition: very good Offer Type: Used Machine Specifications: Capacity: 1040 x 4.0 mm Drive type: el./mech. Propulsion: 7.3 kW Remark: rip fence, Material supports and stop at the front, 2 spare blades Weight: 2000 kg The machine is in a very good condition and ready for immediate use and can be viewed and demonstrated by us. We would be pleased if you are interested in our offer. Errors, modifications and prior sale excepted.
Key data: 2040 mm, 2 mm
Machine Type: Swivel Bending Machine Manufacturer: RAS Model: 2003 M Condition: very good Offer Type: Used Machine Specifications: Capacity: 2040 x 2.5 mm Drive type: el./mech. Propulsion: 0.75 kW Remark: backgauge, 5 additional bending rails Weight: 1800 kg The machine is in good condition and ready for immediate use and can be viewed and demonstrated by us. We would be pleased if you are interested in our offer. Errors, modifications and prior sale excepted.
Offer 23317 Specifications: - Max. working width 2040 mm - max. material thickness at 40 kp / mm², strength 3.5 mm - Bending angle adjustment electronically pre-selectable 0 - 135 ° - Smallest bending radius 1.25 x sheet thickness - Minimum inboard height 6 x sheet thickness - Automatic sequential control for a complete workflow - Operation via hand or foot switch - Maximum opening width / stroke of the upper beam 200 mm - Height adjustability - bending beam 80 mm - the lower beam 80 mm - Upper beam drive 400 V / 1.1 kW - Bending beam drive 400 V / 1.5 kW - Manual backgauge can be operated from the front - Space requirement approx. W 3300 x H 1350 x D 1500 mm - Weight approx. 2600 kg
Key data: 1040 mm, 2 mm
Max. cutting length: 1040 mm Max. sheet thickness: 2.5 mm steel Manual backgauge can be operated from the front up to 500 mm Side stop Knife sharpened Weight: 750 kg
Key data: 1040 mm, 2 mm
Type 52.70 Specifications: Cutting length 1040 mm Sheet thickness in St 2.5 mm Sheet thickness in stainless steel (700 N) 1.5 mm Motorized back gauge up to 500 mm Stroke rate approx. 60 rpm
Key data: 1020 mm, 1 mm
Machine Type: Swivel Bending Machine Manufacturer: RAS Model: 61.1 Year of construction: 1965 Condition: good Offer Type: Used Machine Specifications: Capacity: 1020 x 1.5 mm Drive type: manual Remark: Material support at the back Weight: 220 kg The machine is in good condition and ready for immediate use and can be viewed and demonstrated by us. We would be pleased if you are interested in our offer. Errors, modifications and prior sale excepted.
Lockformer RAS type 22.15 Power: 2,2 kW Maxi thickness: 1,5 mm Wheel diameter: Ø 85 mm x 40 mm Voltage: 380 V Dimensions (L x W x H): 1700 x 600 x 1100 mm Weight: approx 350 kg
Max. sheet thickness: 1.5 mm steel 2 continuous stations (see video) Weight: approx. 500 kg
Max. sheet thickness: 1.5 mm steel 2 continuous stations (see video) Weight: approx. 500 kg
Key data: 2040 mm, 2 mm
Max. cutting length: 2040 mm Max. sheet thickness: 2 mm steel Manual backgauge adjustable from the front up to 550 mm Pneumatic sheet metal holding Knife sharpened Weight: 1100 kg
Max. bending length: 3,200 mm Max. sheet thickness: 2.5 mm steel Segmented upper beam splint Manual and automatic bending mode possible Bending angle adjustment via potentiometer Weight: 3800 kg
Cutting length: 1020 mm Sheet thickness: 1.25 mm Table size: 700 x 1150 mm Weight, approx.: 290 kg Equipment: -Hold - Side stop with angle adjustment and handwheel
cutting length: 3150 mm sheet thickness: 4 mm steel Controlled backgauge up to 1000 mm Side stop and table lengths Cutting length limitation Cut edge illumination Operating instructions Weight approx. 4200 kg
Max bending length: 3200 mm Max sheet thickness: 4 mm steel Weight: approx. 5800 kg Mwauag Motor-controlled rear stop with folding cams up to 1500 mm Motorized bending cheek adjustment Multibend 9000 Control Segmented upper cheek tool with automatic tool clamping (height 150 mm)
