Specifications: 2 castors hydraulically adjustable 3 rollers driven Bending moment: 48 cm/3 Roll diameter: 360 mm Main motor power: 7.5 KW Dimensions (length x width x height): approx. 2000 x 1300 x 1900 mm Weight: approx. 5.5 tons Accessories: various tools The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.
Specifications: Working length: 3050 mm Max. bending power: 30.0 mm Max. bending capacity length 1500 mm: 42 mm Bend: 25.0 mm Diameter upper roller: 460 mm Diameter lower roller: 460 mm Number of driven rollers: 3 hydraulic snap roller bearing Engine power: 37 kW Dimensions (length x width x height): approx. 5850 x 2550 x 2650 mm Weight: approx. 30 tons Note: Compact design, therefore low space requirement Parts of the hydraulics installed under the machine
Description of the offer Horizontal and vertical H + V Shaft Ø105 mm Number of Rolls3 Horizontal Yes Vertical Yes Resistance moment 40 cm³ Flatbed capacity 100 x 25 x 700 mm Tube capacity 100 x 1100 mm Capacity bar 60 x 60 x 600 mm T-profile capacity 100 x 12 x 1000 mm HEA-Profile capacity120 x 800 mm Working speed0 - 400 mm
Description of the offer Horizontal and vertical H + V Shaft Ø105 mm Number of Rolls3 Horizontal Yes Vertical Yes Resistance moment 40 cm³ Flatbed capacity 100 x 25 x 700 mm Tube capacity 100 x 1100 mm Capacity bar 60 x 60 x 600 mm T-profile capacity 100 x 12 x 1000 mm HEA-Profile capacity120 x 800 mm Working speed0 - 400 mm
Max. bending length: 1500 mm Max. sheet thickness: 10 mm steel Upper roll diameter: 195 mm Includes rollers for rolling flat steel Clockwise and anticlockwise rotation via hand-held control unit
Max. length of plate 3000 mm Max. plate thickness 40 mm Number of rolls 3 pcs Upper roll diameter 550 mm Lower roll diameter 450 mm Control Roundo WCN Main motor power 94 Kw Equipped with: Pre-bending, hydraulic Three roll drive Cone bending divice Electro-hydraulic operation of drop-end Top support Side supports Roller conveyor Service tools etc.
Rounds: 225 mm Squares: 75 mm Flats: 0 mm Flats on edge: 0 mm Angles: 75 mm (1) horizontal / (2) vertical: 1 Make Roundo R3 Type R 3 Profile bender Year 1985 Roundo R 3 Horizontal and vertical profile bender Outside diameter max. (mm)Angle 75 x 75 x 7 Inside diameter max. (mm)IPE 140 x 700 Max. pipe length (mm)Shaft 75 mm Max. angle Rolls 225 mm Wall Thickness (mm)Cap. 14 cm3 Remote control
Rounds: 188 mm Squares: 65 mm Flats: 0 mm Flats on edge: 0 mm Angles: 60 mm (1) horizontal / (2) vertical: 1 Make Roundo R2 Type R 2 Year 1995 Roll = 188 mm Outside diameter max. (mm)Shaft = 65 mm Inside diameter max. (mm) 3 rolls driven Max. pipe length (mm)Bend section 7 cm3 Max. anglePower 2.2 kW Wall Thickness (mm) Optical readout Angle 60 x 60 x 6 x 600 IPE 100 x 500 mm T 60 x 60 x 7 x 600
Sheet thickness: 18,00 mm Bending length: 2550 mm Number of rolls: 4 Make Roundo 18 mm Type PS 280 Year 1988 3 roll plate bender Sheet thickness (mm) T = 18 mm Bending length (mm) L = 2.550 mm Number of rolls 3 roller Optical read out position Hardned rolls Hydraulic machine
Sheet thickness: 18,00 mm Bending length: 3000 mm Number of rolls: 3 Make Roundo 18 mm Type PS 310 Year 1980 3 roll hydraulic plate bender Sheet thickness (mm) T = 18 mm Bending length (mm) L = 3.000 mm Number of rolls 3 roller Top roll = 310 mm Hydraulic opperated Dro positions side rolls
Capacity: 360 t Diameter: 140 mm Length: 0 mm Make Roundo R 5 S Type R 5 S Year 1989 Section modulus 50 cm3 Outside diameter max. (mm)Top shaft = 140 mm Inside diameter max. (mm)Lower shaft = 120 Max. pipe length (mm)Rolls = 360 Max. angle Power = 11 kW Wall Thickness (mm) Weight 4000 Kg Tube = 142 x 1.800 mm HEA = 140 x 900 mm Some tooling
Rounds: 0 mm Squares: 0 mm Flats: 0 mm Flats on edge: 0 mm Angles: 0 mm (1) horizontal / (2) vertical: 1 Make Roundo R 5 S Type R 5 S Year 1989 Section modus 48 cm3 Outside diameter max. (mm) Roll = 385 mm Inside diameter max. (mm) Power 7.5 kW Max. pipe length (mm)Flatt 100 x 30 Max. angle U over Y = 200 Wall Thickness (mm)U over X = 100 Speed 0 - 7 M/min.Set with rolls Hor. & Vert. opperated
Sheet thickness: 35,00 mm Bending length: 1000 mm Number of rolls: 4 CNC Brand: _Unknown / Other CNC Model: Roundo CNC
Sheet thickness: 20,00 mm Bending length: 2000 mm Number of rolls: 3
Rounds: 3 mm Squares: 1 mm Flats: 1 mm Flats on edge: 1 mm Angles: 1 mm (1) horizontal / (2) vertical: 1 Profile bending machineROUNDO - R-72-S MACH-ID 8888 Make: ROUNDO Type: R-72-S Year: 1999 Horizontal + Vertical Shaft Ø240 mm Number of rolls3 Resistance moment320 CM³ Capacity flat175 x 40 x R=1200 mm Capacity Tube190 x R=2500 Ø x mm Capacity bar110 x 110 x R=1500 mm Capacity T-Profile160 x 20 x R=1400 mm Capacity HEA-Profile240 x R=1500 mm Working speed0 - 7000 mm/min. Adjustment siderolls0 - 400 Side supports Fully hydraulic machine Hydraulic side support in & out Hydraulic side support up & down Set universal rolls Read out system Positioning side rolls
sheet width: 1500 mm plate thickness: 10,00 mm pre-bending: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Top roller diameter: 195 mm Includes rollers for rolling flat steel Clockwise and anti-clockwise rotation via handheld control unit The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hydraulic machine Can work in horizontal and vertical positions 3 driven rolls Type: 3 rolls Dia rolls: 225 mm Dia of die mandrel: 75 mm Rotationspeed: 7 m/min Motorpower: 4 HP Length : 1000 mm Depth: 980 mm Height: 950 mm Weight: 1200 kg
Sheet thickness: 7,00 mm Bending length: 1000 mm Number of rolls: 1 Max plate thickness : 7 mm Min. rolling diameter : 760 Max. rolling diameter : 600 Top Shaft diameter : 110 Lower rolls diameter : 120 Max. bending power : 350.000 N Rolling width 1,000 mm Rolling thickness prebending 7 mm Number of rolls 1 Number of driven rolls 1 Power 2.4 kW
Sheet thickness: 40,00 mm Bending length: 3000 mm Number of rolls: 4 SPECIFICATIONS Controll Conventionel Hydraulic / Mechanical Hydraulic 3 or 4 roll 4 roll Maximum sheet thickness 40 mm Bending length 3000 mm Max. Rolling capacity Ø 2.500 38 mm Max. Prebending capacity Ø 2.500 25 mm Top Roll Ø 460 mm Bottom Roll Ø 460 mm Side Rolls Ø 390 mm Power 55 kW
Rounds: 188 mm Squares: 65 mm Flats: 0 mm Flats on edge: 0 mm Angles: 60 mm (1) horizontal / (2) vertical: 1 Make Roundo R2 Type R 2 Year 1995 Roll = 188 mm Outside diameter max. (mm)Shaft = 65 mm Inside diameter max. (mm) 3 rolls driven Max. pipe length (mm)Bend section 7 cm3 Max. anglePower 2.2 kW Wall Thickness (mm) Optical readout Angle 60 x 60 x 6 x 600 IPE 100 x 500 mm T 60 x 60 x 7 x 600
Rounds: 225 mm Squares: 75 mm Flats: 0 mm Flats on edge: 0 mm Angles: 75 mm (1) horizontal / (2) vertical: 1 Make Roundo R3 Type R 3 Profile bender Year 1985 Roundo R 3 Horizontal and vertical profile bender Outside diameter max. (mm)Angle 75 x 75 x 7 Inside diameter max. (mm)IPE 140 x 700 Max. pipe length (mm)Shaft 75 mm Max. angle Rolls 225 mm Wall Thickness (mm)Cap. 14 cm3 Remote control
Sheet thickness: 20,00 mm Bending length: 2000 mm Number of rolls: 3
Sheet thickness: 35,00 mm Bending length: 1000 mm Number of rolls: 4 CNC Brand: _Unknown / Other CNC Model: Roundo CNC
Rounds: 0 mm Squares: 0 mm Flats: 0 mm Flats on edge: 0 mm Angles: 0 mm (1) horizontal / (2) vertical: 1 Make Roundo R 5 S Type R 5 S Year 1989 Section modus 48 cm3 Outside diameter max. (mm) Roll = 385 mm Inside diameter max. (mm) Power 7.5 kW Max. pipe length (mm)Flatt 100 x 30 Max. angle U over Y = 200 Wall Thickness (mm)U over X = 100 Speed 0 - 7 M/min.Set with rolls Hor. & Vert. opperated
Capacity: 360 t Diameter: 140 mm Length: 0 mm Make Roundo R 5 S Type R 5 S Year 1989 Section modulus 50 cm3 Outside diameter max. (mm)Top shaft = 140 mm Inside diameter max. (mm)Lower shaft = 120 Max. pipe length (mm)Rolls = 360 Max. angle Power = 11 kW Wall Thickness (mm) Weight 4000 Kg Tube = 142 x 1.800 mm HEA = 140 x 900 mm Some tooling
Sheet thickness: 18,00 mm Bending length: 3000 mm Number of rolls: 3 Make Roundo 18 mm Type PS 310 Year 1980 3 roll hydraulic plate bender Sheet thickness (mm) T = 18 mm Bending length (mm) L = 3.000 mm Number of rolls 3 roller Top roll = 310 mm Hydraulic opperated Dro positions side rolls
Sheet thickness: 18,00 mm Bending length: 2550 mm Number of rolls: 4 Make Roundo 18 mm Type PS 280 Year 1988 3 roll plate bender Sheet thickness (mm) T = 18 mm Bending length (mm) L = 2.550 mm Number of rolls 3 roller Optical read out position Hardned rolls Hydraulic machine
