Plastic waste pelletizing line – compactor + ZL 100 extruder,
200–300 kg/h (used, completely overhauled)
POL-SERVICE Majcher – manufacturer and supplier of plastic
processing machines with over 30 years of experience.
We offer a complete plastic waste pelletizing line designed for
processing LDPE/LLDPE/HDPE film waste, production scrap (straps,
mouldings, parts), mixed plastics and light packaging waste.
The line is based on a compactor and a ZL 100 single-screw extruder
Ø100 mm with double degassing and a water ring pelletizing system.
The plasticizing unit (screw and barrel) is NEW. The line has
undergone a complete overhaul and is ready for industrial operation.
Line configuration – main components
1. Belt conveyor to compactor
– Motor power: 1.5 kW
– Belt width: 700 mm
2. Compactor
– Motor power: 55 kW
– Compactor diameter: 800 mm
– Number of rotating knife groups: 3
– Number of fixed knives: 17 pcs
– Internal temperature sensor in the compactor
– Compactor jacket cooling system: water and air
3. ZL 100 single-screw extruder
- Screw: 38CrMoA1A, nitrided – NEW
- Barrel: 38CrMoAlA, nitrided, air-cooled – NEW
– Main drive: 90 kW A.C. motor with inverter
– Screw diameter: Ø100 mm
– L/D ratio: 36:1
– Max. screw speed: 140 rpm
– Degassing system: double venting, vacuum pump 3 kW
– Number of heating zones: 7
– Air cooling, cooling power: 0.37 kW × 7
– Line throughput: approx. 200–300 kg/h (depending on material and
operating conditions)
4. Hydraulic plate screen changer 2ר200
– Max. pressure: ≤ 20 MPa
– Screen change without stopping the extruder, no leakage, screen
change time ≤ 2–3 seconds
– Material: 38CrMoAl
– Heating power: 12 kW
Ensures continuous melt filtration and stable pressure and granulate
quality.
5. Water ring pelletizer
– Die head material: 40Cr, nitrided
– Heated die head
– Knife speed controlled by inverter
– Number of cutting knives: 2–4 pcs, made of W18Cr4V
- Strand die: 25 holes
6. Centrifugal dryer
– Water tank made of stainless steel
– Water pump motor: 4 kW
– Max. throughput: approx. 500 kg/h
7. Vibrating screen/table
– Vibrator motor power: 2 × 0.32 kW
– Screening mesh made of stainless steel
8. Material conveying system and silo
– Transport fan/blower motor: 3.7 kW, speed 2800 rpm
– Pipe diameter: Ø100 mm
– Silo capacity: 1 m³
– Throughput: approx. 500 kg
– Injector and conveying pipes made of stainless steel
– Storage tank made of stainless steel
Price and warranty
– price after complete overhaul
– The line is covered by a 6-month warranty
Tests, technological acceptance and commissioning
– It is possible to carry out test runs of the line at our facility
using the Customer's material – this allows verification of
throughput, pellet quality and optimisation of process parameters.
– The line price includes a technological acceptance with a trial
run at our plant using the Customer's material.
– At extra cost, we can provide on-site commissioning at the
Customer's plant and staff training in operation, adjustment and basic
maintenance.
On request we can assist with:
– adapting the line configuration to specific materials and required
capacities,
– integration into an existing plant (feeding, storage, dedusting,
additional recycling stages).
For over 30 years POL-SERVICE Majcher has specialized in the
production and overhaul of plastic processing machines. We offer
extruders, complete profile lines, granulation lines, recycling lines,
mills, shredders and other auxiliary equipment. We provide
plasticizing systems, heaters, wear parts, commissioning services and
test runs on the Customer's material. Feel free to check our other
machine offers.