Oiler, proportional standard mist lubricators FESTO series D LOE-D-MIDI 192576 Operating pressure: 1 - 16 bar Minimum flow rate for lubricator function: 8 l/min Oil capacity: max. 110 cm3 New ! Dimensions: 205 x 55 x 55 mm
Wear parts kit FESTO DNC-63-PPV-A 369198 Series: M2 New, with documents ! Dimensions ( packaging ): 120 x 100 x 35 mm
Wear parts kit FESTO DNC-32-PPV-A 369195 Series: M1 New, with documents ! Dimensions ( packaging ): 120 x 85 x 35 mm
Bearing cover, bearing cover-BG, 4 pieces FESTO ADN-25 665699 Piston rod diameter: Ø 10 mm New ! Dimensions: 40 x 40 x 13.5 mm
Precision pressure regulating valve, pressure regulator FESTO LRP-1/4-0.7 159500 Operating pressure: 1 - 12 bar Pressure control range: 0.05 - 0.7 bar Pneumatic connection: 2x G1/4, 2x G1/8 ( pressure gauge ) New ! Dimensions: 50 x 50 x 110 mm
Branch module, 2 pieces FESTO FRM-D-MIDI 170685 0 - 16 bar Connections: G1/2, G1/4 ( inch ) New ! Dimensions ( one module ): 55 x 55 x 62 mm
Solenoid valve, directional control valve FESTO JMEBH-5/2-5,0-B-230AC 173110 1,5 - 8 bar Control solenoid : 2x MSEB-3-230V AC 663955 Control voltage : 198 - 253 V AC 3.0 / 2.4 VA 50 / 60 Hz used, tested ! Dimensions ( valve ): 148 x 18 x 50 mm
Solenoid valve, directional control valve, pilot-operated, throttle FESTO CM-5/2-1/4-FH 6154 1.5 - 8 bar without solenoid coil New ! Dimensions ( valve ): 120 x 32 x 81 mm
Stopper cylinder, pneumatic cylinder, double-acting, pulling FESTO DFSP-16-10-S-PA 576056 Piston diameter: Ø 16 mm stroke: 10 mm Rod diameter: Ø 10 mm 2.8 - 10 bar New ! Dimensions: 120 x 66 x 40 mm
Mini slide, pneumatic cylinder, double-acting FESTO SLT-16-50-A-CC-B 197897 Piston diameter: Ø 16 mm stroke: 50 mm Rod diameter: Ø 6 mm 1 - 8 bar carriage: 65 x 66 mm yoke plate: 65 x 38 x 10 mm Base plate: 100 x 66 mm New ! Dimensions: 120 x 66 x 40 mm
Solenoid valve, directional control valve FESTO JMVH-5-1/4-B 19136 2 - 10 bar Control voltage : 20.4 - 26.4 V DC used, tested ! Dimensions (valve): 255 x 33 x 53 mm
With the Festo ZA tenon cutter, straight, under-shouldered and offset tenons can also be cut in one operation combined with slots, milling and cutting to length., Aggregate: 5, aggregate 1: Saw Bottom, 2.5 HP, aggregate 2: Saw Top, 2 HP, aggregate 3: Slot cutter below, spindle: ø 30 mm, aggregate 4: Slot cutter above, spindle: ø 30 mm, aggregate 5: Milling spindle, spindle: ø 40 mm, clamping length: 100 mm, 5 HP, clamping: Pneumatic, table length approx.: 1.700 mm, length x WIDTH X HEIGHT: 2.6 x 2 x 1.5m
