Manufacturer: Homag Doppelzerspaner mit Schutzfräsen, Spare part from machine: Homag, for left machine side: yes, Number of motors: 3, Motor : Perske, kW-Leistung : 3/4,4, Volt/Hz : 50/100, Drehzahlen U/min : 2880/5860, Siko Anzeige : yes, Pneumatically controlled: yes/mit Revolver, Slewable horizontal 3: yes, FREE TEXT: Nur Ständer ohne Motore,
Manufacturer: Homag CPU SPS-II, Type: Homatic, Model: PC-Controller, Serial number: 2-083-01-5053,
Manufacturer: ELTEC Homag IPC-2, Type: Homatic, Model: Netzwerkkarte, Serial number: 2-083-03-0099, Systemconfiguration: IPCA-200/1, Serial number: Traegerkarte,
Manufacturer: Homag mit Verleimteil, Type: Optimat BOF / 40 / G , Year: 2000, Control: WoodWOP, Programmierplatz Büro: yes, Work piece width min-max mm: 1050/1200, Min.-max. workpiece length in mm: 4800, Min.-max. workpiece height in mm: 60/200, C axis: yes, Tool adaption system: HSK F63, Milling engine 1 hours power: 12, rpm 1): 1500 - 18000, Number of tool changers: 1, Number of tools per tool-magazine: 12, Mitfahrender Werkzeugwechsler: yes, Vertical drills-X: 11, Drill vertical Y: 7, Horizontal drills-X: 4, Aluminium sleeking table: yes, 2 station allocation: 2, Stops in the table front: 6 , Vacuum pumps m³/h: 120, Saw unit: yes, Edgebanding unit: no, Marking laser: Laserpositionerhilfe, Radial arm machine: yes, Foot mats: yes, Available: ca. 03/2017, Year :2000
Manufacturer: Eltec Homag, Type: Homatic, Model: Seco 6xRS232 VME Bus IRQ2, Serial number: 2-083-03-0202,
Manufacturer: Homag CPU , Type: SPS II 12 MHz 1MB RAM, Serial number: 2-083-01-5044,
Manufacturer: Homag CPU SPS-II, Type: 1 MB RAM und PC Cobtroller, Serial number: 2-083-01-5043, Year: 93, Year :93
Manufacturer: Homag CPU, Type: CPU HC020 SPS II, Serial number: 2-083-01-50-60, Systemconfiguration: V:4.66a,
Manufacturer: Homag, Type: Homatic, Model: Eingangskarte 3224 Volt, Serial number: 2-083-01-5105, Year: 93, Year :93
Manufacturer: Homag, Type: Homatic Streckenprozzessor , Serial number: 2-083-02-7024,
Manufacturer: Umrichter Homag KEB, Model: für Weeke Frässpindel, Serial number: 97410930-0316782, mH/Hz: 16000, Output PpK= kW: 11 kw, Used: yes,
Manufacturer: Homag Ausgangskarte 24 Volt, Type: Homatic, Model: Ausgangskarte 16 24 Volt, Serial number: 2-083-01-5408,
Manufacturer: Homag CPU SPS CPU, Type: Homatic, Serial number: 2-083-01-5057, Systemconfiguration: 2-083-01-5020 REV02, Year: 11/94, Year :11/94
Manufacturer: Homag Ziehklingenaggregat, Ausführung rechts: yes, Radiusziehklinge: yes, Steuerbar: no, Tracing by roller: yes, Wechselstähle: yes, Wendemesser: yes, Radien 2/3 mm: yes, Automatischer Radienwechsel: no, Ständeraufbau: yes, Kettenbahn/Oberdruck: yes,
Manufacturer: Homag, Type: Optimat BAZ 311/40/K, Year: 2007, Software: PC85 CNC CORE Z, Feeding speed max m/min: X,Y-80, Z-30, Working range X: 4000, Working range Y-axis: 1220, Working range Z: 12-300, Year :2007
Manufacturer: Homag Ziehklingenaggregat, Ausführung rechts: yes, Radiusziehklinge: yes, Steuerbar: no, Tracing by roller: yes, Wechselstähle: yes, Wendemesser: yes, Radien 2/3 mm: yes, Automatischer Radienwechsel: no, Ständeraufbau: yes, Kettenbahn/Oberdruck: yes,
Manufacturer: Homag Anschlaglineal gesteuert, Type: aus KFL 10, FREITEXT1: Pneumatisch gesteuert, FREITEXT2: 8 fach Revolver, FREITEXT3: 10 mm Schiene, FREITEXT4: mit Befestigung Kettenbahn,
Manufacturer: Homag BAZ , Type: 211 Venture 22 L, Year: 2006, Control: Woodwop/Powercontrol PC 85, Software: Softwarepaket AV, Work piece width min-max mm: 4400 X 1550, Feeding speed max m/min: X= 80/Y=80/Z=30, C axis: yes/Schnittstelle Flex 5, Pendulum processing: yes, Work piece width min-max mm: 4400 X 1550, Number of milling spindles: 1, Number of milling spindles vertical: 1, Tool adaption system: HSK 63 F, Milling engine 1 hours power: 12, rpm 1): 1500-24000, Number of tool changers: 1, Tellerwechseler: 1, Pickup Wechlser: Verleimteil/Easy Edge, Number of tools per tool-magazine: 18, Vertical drills-X: 11, Drill vertical Y: 7, Horizontal drills-X: 1, Drill horizontal Y: 2, Traverse table: 8 Traversen, 2 station allocation: yes, Stops in the table front: yes, Stops in the table rear: yes, Vacuum pumps m³/h: 250, Saw unit: yes, Edgebanding unit: yes, Edgeband hight mm: 60, LED-R ...
Manufacturer: Perske Umrichter, Year: 1996, Type: 2004 neugewickelt, Year :1996
Manufacturer: Homag PU und EVA, Type: KAL 310 310/6/A3/S2, Year: 2008, Control: NC 22, Software: Homag, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 65, Min.-max. workpiece length in mm: 250, Min.-max. workpiece height in mm: 12-60, Min-max feed m/min: 10-25, Premilling: yes, Fine milling: yes, Application of separation agent: yes, IR zone: yes, Coil magazine: 2-fach, Mitre stations: HL 81, Bevel milling: yes, Corner tracing type: FF 12, 4 motors: Ja, Radius scraper: yes, Type of scraper: PN 10, Flat scraper: FA 11, 4 motors: Ja, Ersatzverleimteil : PU, Bonding part EVA: EVA, Buffing unit: yes, Separation agent setup: yes, Year :2008
Manufacturer: Homag, Type: KLO 76, Year: 1994, Min-max edge material mm: 0,5-3,0, Min.-max. workpiece length in mm: 150, Edgeband height max mm: 55, Min-max feed m/min: 10-25, Premilling: no, IR zone: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, radius milling: yes, 4 motors: yes, Radius scraper: yes, Flat scraper: yes, 4 motors: yes, Ersatzverleimteil : yes, Bonding part EVA: yes, Pre-smelting Kg/Hr: yes, Buffing unit: yes, Top pressure belt/roller: yes, Roller/belt: Riemen, Compressed air bar: 6, Machine lenght mm: 7500, Noise enclosure: yes, Year :1994
Manufacturer: Homag, Type: Rechnerkarte, Model: CPU-Karte 70 BO 10 MHz 2 RAM, Serial number: 4-086-05-194,
Manufacturer: Homag , Spare part from machine: KL Seire, Year: 1999, Gluing part left side: yes, for left machine side: yes, Kantenmagazin : 10 fach, Own drive: yes, Min-max height of gluing part mm: 60, Pressure rollers: 5, Temperature control: yes, Min.-max. trimming shears mm: 60, Magazinschächte : 10, Axis-controlled: yes Schräge 20 Grad, Slewable horizontally: yes, Year :1999
Manufacturer: Homag Tellerwechsler, Year: 1999, Type: 8 Fach Wechsler, Length mm: Ersatzteil aus Weeke 195 T, Year :1999
Manufacturer: Homag, Spare part from machine: KF, for right machine side: Rechts, Number of motors: 2, kW-Leistung : 0,62/300 HZ, Drehzahlen U/min : 18000, Siko Anzeige : yes, Horizontal Rollentastung : yes, Vertical roller sensing: yes, Pneumatically controlled: 8-fach Revolver, Revolver adjustment: yes, Slewable horizontally: yes, pneumatisch gesteuert : yes, FREE TEXT: Profilverstellung Pneumatisch,
Manufacturer: Indramat Motor mit Getriebe Atlanta, Year: 1999, Type: MAC93C-0-FS/4HC/110-A-0, Kw output: ca.10, Bauart Flanschmotor: yes, Preis pro Stück Euro: 1500, Available: sofort, Year :1999
Manufacturer: Homag Fräsständer Bündigfräsaggregat, Spare part from machine: KF Maschine, for right machine side: rechts, Number of motors: 2, kW-Leistung : 1,1, Drehzahlen U/min : 18000, Siko Anzeige : yes, Horizontal Rollentastung : yes, Vertical roller sensing: yes, Pneumatically controlled: no, kW-output 2: 1,1/300,
Manufacturer: Homag, Type: 2 Achser HC 010 o.Analogeingang, Model: 2-Achser F.mini-Controller Rev, Serial number: 2-083-02-8071,
Manufacturer: Homag PU Verleimung , Type: KL 79/2/A20/S2, Control: Homatic NC 21, Work piece width min-max mm: 60, Min-max feed m/min: 10-25, Axis control: Einlauflineal, Einlauflineal gesteuert: yes, Premilling: yes, Fine milling: yes, Application of separation agent: yes, IR zone: yes, Coil magazine: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Pre-milling: yes, Corner tracing type: FK 13, 2 motors: yes, Vertical grooves: 2, Grooves, slewable-controlled: yes, Radius scraper: yes, Scraper with axis adjustment: yes, Flat scraper: yes, Spraying system 2: yes, Ersatzverleimteil : PU, Bonding part EVA: yes, Edge sanding: KS 10, Profile sanding top bottom: yes, Buffing unit: yes, Top pressure belt/roller: Band, Work piece refeeding: Bartgstedt ZHR, Compressed air bar: 6,
